System Works 99101100 manual Section V. Initial START-UP and Restart Instructions

Page 6

SECTION V. INITIAL START-UP AND RESTART INSTRUCTIONS.

1.Be sure all connections have been made and are secure.

2.Make sure the hair and lint pot of the pump is filled with water. (FAILURE TO FILL THE HAIR AND LINT POT WITH WATER WILL RESULT IN DAMAGE TO THE PUMP AND PUMP SEAL).

3.OPEN THE HIGH FLOW MANUAL AIR RELIEF VALVE UNTIL IT SNAPS INTO THE FULL OPEN POSITION (THIS ONLY REQUIRES A 1/4 TURN COUNTERCLOCKWISE).

4.STAND CLEAR OF THE FILTER. Start pump allowing the filter tank to fill with water. Close the high flow air relief valve after a steady stream of water appears.

5.Your filter has now started its filter cycle. You should check that the water is returning to the pool and take note of the operating pressure. My original starting pressure is ___________ PSI with the filter clean.

6.Check the system for water leaks. If a leak is found, shut off pump before correcting the leak.

WARNING

This filter operates under high pressure. When any part of the circulating system (e.g., lock ring, pump, filter, valves, etc.) is serviced, air can enter the system and become pressurized. Pressurized air can cause the lid to be blown off which can result in severe injury, death, or property damage.

7.As the filter removes dirt and impurities from the pool water, the accumulation will cause the filter pressure to rise and the flow to diminish. When the pressure gauge reading is 8 to 10 PSI higher than the clean filter reading noted above, it is time to clean the filter’s element grids, see SECTION VI.CLEANINGTHEFILTER,below.

SECTION VI. CLEANING THE FILTER

1.Cleaning frequency will vary from pool to pool and with other factors such as weather conditions, heavy rains, dust pollen, bather load and water chemistry. Check the pressure gauge reading on a regular basis and when the pressure gauge reading increases 8 to 10 PSI over the initial clean filter reading, it is time to clean your CARTRIDGE ELEMENT.

2.Turn the pump off, shut off any automatic controls to assure that the system is not inadvertently started during servicing.

3.Plug the skimmer port with a rag. This will prevent pool water from running out during servicing.

4.Open the filter High Flow™ manual air relief valve, and the filter drain plug.

5.Remove the hair and lint strainer pot lid and clean the basket. Replace the basket and secure the lid.

6.Remove the filter lock ring by depressing the two spring loaded locking blocks and rotating the ring counter clockwise until the ring is free from the filter body.

7.Remove the filter lid using the lifting handles on the lid.

P/N 99101100

6

REV. F 5-1-01

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Table of Contents Readandfollowallinstructions Section I. Pump Safety InstructionsSection II. HOW Your Filter Works SavetheseinstructionsSection III. Check Valve Installation Instructions InstallationSection IV. Installation InletPool Section VI. Cleaning the Filter Section V. Initial START-UP and Restart InstructionsDo not USE a PETROLEUM-BASE Lubricant on the O-RING Section VIII. Cleaning the High Flow Manual AIR Relief Valve Section VII. WinterizingthefilterSection Trouble Shooting Section Pump InstructionsTheelectricmotor Section XI. Technical Data Filter and Tank Replacement PartsMaxim Pump Dynamo Pump Section XI. Technical Data Dynamo Pump REV. F

99101100 specifications

System Works 99101100 is a comprehensive software suite designed for users seeking an integrated solution for system optimization, maintenance, and productivity enhancements. This all-in-one tool serves as a reliable companion, ensuring that personal computers run at peak performance through a variety of advanced features and technologies.

One of the primary characteristics of System Works 99101100 is its intuitive user interface that simplifies navigation, allowing users of all levels to access the tools they need quickly. The suite includes a powerful disk management utility that optimizes disk performance by defragmenting and reorganizing data on hard drives. This ensures faster data access and improved efficiency, prolonging the lifespan of storage devices.

The suite also incorporates effective virus protection and security features. With built-in antivirus capabilities, System Works 99101100 scans for and eliminates potential threats before they can compromise system integrity. Regular updates ensure that the software remains current with the latest security definitions, giving users peace of mind while browsing the internet or downloading files.

Another noteworthy feature is the system recovery tool, which assists users in restoring their systems to a previous state in case of failure or unwanted changes. This functionality is crucial in today's computing environment, where data loss can occur due to various unforeseen events. System Works 99101100 helps safeguard important files, ensuring that critical data remains recoverable.

In terms of performance tuning, the suite includes tools designed to optimize startup programs, manage system resources, and configure system settings. This level of customization allows users to tailor their computing experience according to their specific needs, enhancing productivity by streamlining workflows.

Additionally, System Works 99101100 is equipped with a detailed reporting system that offers insights into system health and performance benchmarks. Users can track progress over time and make informed decisions about necessary maintenance activities.

In conclusion, System Works 99101100 presents an array of features that focus on enhancing user experience by providing efficient solutions for system maintenance, security, and optimization. Its combination of usability, cutting-edge technology, and comprehensive functionality makes it a standout choice for anyone looking to improve their computing environment. With such a robust toolkit, users can enjoy a seamless and productive experience, free from common technical hindrances.
Top Page Image Contents