Tecumseh LV156XA, LV195EA, LV156EA, LV195XA specifications II. Choke Only, Primer Bulb Vent Hole

Page 13

3.When starting a cold engine, push primer bulb firmly 3 times, allowing primer bulb to return completely to orig- inal position between pushes. See Figure 24.

NOTES

Be sure to cover vent hole when pressing primer bulb. See Figure 24.

Cooler temperatures may require pushing primer bulb firmly 5 times.

DO NOT use primer to restart a warm engine after a short shutdown. Doing so will flood the engine and may result in equipment malfunction.

4.Operate equipment control to release engine brake or clutch, if present (see equipment manufacturer’s instructions). See Figure 21 on page 10. Afterward, continue reading instructions below.

 

 

When pulling starter rope, the rope

WARNING

 

 

can unexpectedly jerk back toward

 

 

 

 

engine causing serious injury. To avoid this risk, carefully follow these instructions:

5.Grasp starter cord handle. See Figure 21 on page 10. Afterward, continue reading instructions below.

a.Pull rope out slowly until you feel drag.

b.Without allowing the rope to retract, continue pulling rope with one rapid full arm stroke.

c.Return rope slowly to original position.

NOTE

Following the instructions listed in the steps above avoids potential damage to the recoil mechanism.

6.If engine fails to start after 3 attempts repeat steps 2 thru 5 and try again.

7.If engine does NOT start after following steps 1 thru 6, contact your Authorized TecumsehPower Servicing Dealer. DO NOT attempt to start or troubleshoot this engine in any other way.

II. Choke Only

1.To avoid carbon monoxide poisoning, be sure engine is outdoors in a well-ventilated area.

2.Move engine throttle control to “CHOKE” or “START” position, if present (see equipment manufacturer’s instructions). See Figures 21 thru 23 on page 10. Afterward, continue reading instructions below.

NOTE

If restarting a warm engine after a short shutdown, move engine throttle control to “FAST” position instead of “CHOKE” or “START” position. See Figures 21 thru 23 on page 10. Afterward, continue reading instructions below.

3.Operate equipment control to release engine brake or clutch, if present (see equipment manufacturer’s instructions). See Figure 21 on page 10. Afterward, continue reading instructions.

1

2

1. Primer Bulb

2. Vent Hole

Figure 24. Pressing Primer Bulb

 

 

When pulling starter rope, the rope

WARNING

 

 

can unexpectedly jerk back toward

 

 

 

 

engine causing serious injury. To avoid this risk, carefully follow these instructions:

4.Grasp starter cord handle. See Figure 21 on page 10. Afterward, continue reading instructions below.

a.Pull rope out slowly until you feel drag.

b.Without allowing the rope to retract, continue pulling rope with one rapid full arm stroke.

c.Return rope slowly to original position.

NOTE

Following the instructions listed in the steps above avoids potential damage to the recoil mechanism.

5.If engine fails to start after 3 attempts repeat steps 2 thru 4 and try again.

6.When engine starts:

a.Move engine throttle control to “FAST” position.

b.Next, move engine throttle control to desired speed in “RUN” range.

NOTES

If engine starts but falters when engine throttle control is moved to “FAST” position:

a.Move engine throttle control back to “CHOKE” position. See Figures 21 thru 23 on page 10. Afterward, continue reading instructions below.

b.Next, move engine throttle control to “FAST” position.

If engine dies after engine throttle control is moved to “FAST” position, repeat steps 2 thru 6 to restart engine.

7.If engine fires but does NOT continue to run, move engine throttle control to “FAST” position and start engine.

8.If engine fails to start after 3 attempts in the “FAST” position, move engine throttle control to “CHOKE” position and start engine.

9.If engine does NOT start after following steps 1 thru 8, contact your Authorized TecumsehPower Servicing Dealer. DO NOT attempt to start or troubleshoot this engine in any other way.

181-1215-14

Four-Cycle Engine • Vertical Crankshaft • Air-Cooled

Page 11

Image 13
Contents LV148EA/LV148XA LV156EA/LV156XA TecumsehPower Contact Information Safety DefinitionsAdult Supervision of Operation, Refueling and Maintenance General Safety PrecautionsAvoid Carbon Monoxide Poisoning Avoid Gasoline FiresAvoid Burns and Fire from Hot Surfaces Do not Modify EngineAvoid Accidental Starts Use Hearing ProtectionEngine Identification Decal II. How to Get ServiceTechnician’s Handbook IV. Before Starting Your Engine III. Oil and Fuel SpecificationsOil FuelOil Fill Cap/Dipstick Filling Oil SumpII. Oil Fill Cap/Plug Filling Fuel Tank Engines with Electric Starters Starting Your EnginePrimer Bulb Only If your engine has Go toAir Cleaner Primer Bulb Carburetor Muffler Spark Plug Cap Spark Plug WireII. Choke Only Temperatures Below 40F 5C Temperatures Above 40F 5CIII. Primer Bulb and Choke Engines with Recoil Starters Engines with Recoil StartersPrimer Bulb Vent Hole III. Primer Bulb and Choke VI. Stopping Your Engine and Short-Term Storage VII. MaintenanceChecking and Changing Oil Draining Oil Sump Typical Spark Plug Connection Oil Drain Plug Locations Oil Fill Plug Removing Debris from Engine Cleaning/Replacing Air CleanerSpark Plug Servicing Foam FiltersIV. Removal and Installation-Type B Air Cleaner III. Removal and Installation-Type a Air CleanerII. Servicing Paper Filters VI. Removal and Installation-Type D Air Cleaner Removal and Installation-Type C Air CleanerRetainer Slot Flange Paper Filter Tab Cover VIII. Transporting Your Engine AdjustmentsCarburetor Engine SpeedShort-Term/Seasonal Storage IX. Storing Your EngineExtended Storage IV. BatteryDraining Fuel II. Oil Cylinder BoreMaintenance Intervals XI. Maintenance IntervalsProcedure Preventing Forest, Brush and Grass FiresEvery 25 Hours or 3 Months 1. Clean Foam Filter Every 200 Hours or Seasonally 1. Replace Spark Plug Every 25 Hours or 3 Months 1. Change OilFour-Cycle Engine Vertical Crankshaft Air-Cooled California & US EPA Emission Control Warranty Statement Emission Control System Warranty Consumer USE Commercial USE XII. Warranty Information

LV195EA, LV156EA, LV156XA, LV195XA specifications

Tecumseh is a well-known player in the field of small engines, and their LV series, including the LV156EA, LV156XA, LV195EA, and LV195XA, showcases their commitment to innovation and reliability. Designed for various applications, these engines are favored in lawn care equipment, utility vehicles, and more.

The LV156EA and LV156XA models feature a robust design, emphasizing durability and ease of use. They are powered by a 4-cycle, single-cylinder layout, which balances power and efficiency. Equipped with an electronic ignition system, these engines ensure quick starts and reliable operation in diverse conditions. The LV156 series typically has a displacement of approximately 156cc, which delivers a commendable power output suitable for light to medium-duty tasks.

On the other hand, the LV195XA and LV195EA models elevate the performance bar with a larger displacement of around 195cc. This additional capacity translates to higher torque and increased power output, making them ideal for more demanding operations. Both models also feature a heavy-duty crankshaft and a cast-iron cylinder liner, ensuring prolonged engine life and superior wear resistance.

A standout feature across the LV series is Tecumseh’s commitment to low emissions and fuel efficiency. The engines integrate advanced combustion technology, optimizing fuel mix for cleaner combustion. This is particularly beneficial for commercial users, as reduced emissions can help meet stringent environmental regulations.

Moreover, Tecumseh's LV series incorporates user-friendly design elements such as an integrated recoil starter and easy-access oil fill, streamlining maintenance tasks. The lightweight construction aids in portability while providing stability during operation.

Overall, the LV156EA, LV156XA, LV195EA, and LV195XA engines from Tecumseh exemplify a blend of innovative technology, robust performance, and environmental responsibility, making them reliable choices for various applications in the small engine market. Whether for residential, commercial, or industrial use, these engines showcase Tecumseh's dedication to quality and performance in the small engine segment.