Windsor 10027110 Weekly Maintenance, To 6 Month Maintenance, AT the END of Each Work Period

Page 10

MAINTENANCE

WEEKLY MAINTENANCE

1.Use a hydrometer to check the condition of each battery cell.

2.Check battery cable clamps. Ensure clamps are tight on battery terminals.

3.Clean tops of batteries with a wet cloth and a solution of water and baking soda. Wipe battery tops dry after cleaning.

4.Check pad lock for looseness or damage.

5.Check filter and filter seals. Airflow should be unobstructed through filter.

6.Ensure that the pivot points and casters are properly lubricated.

7.Tighten any loose screws or nuts.

4 TO 6 MONTH MAINTENANCE

1.Remove batteries-clean battery tray and battery compartment.

2.Clean battery cable clamps and battery terminals.

3.Check the carbon motor brushes in the pad driver motor.

4.Use a vacuum to remove lint or dust build-up from motor windings.

5.Grease axles.

AT THE END OF EACH WORK PERIOD:

1.Wipe down the exterior of the machine.

2.Lower the deck.

3.Open the cover.

4.Charge the batteries. (See battery charging procedure on page 4-1.)

SHUNT ADJUSTMENT

This pad pressure meter adjustment is factory set. Over the course of time it may become necessary to adjust this setting using the slotted connection on the shunt.

SHUNT ADJUSTMENT (Cont.)

Check the amp range when nuisance tripping of the circuit breaker indicates that the shunt may be out of adjustment.

1.Connect a DC ampere meter to the positive battery lead. Running the machine with a pad, lower the pad to the floor until it is operating at 55-60 amps.

2.Moving the wire in the slot, adjust the pad pressure meter until the needle sets at the line between the green and red areas.

3.Check the other points indicated in the diagram above. The high end should trip the circuit breaker. Replace the pad pressure meter if the approximate amp ranges shown cannot be set.

SHAFT ADJUSTMENT

If shaft is replaced make sure it is adjusted correctly upon installation.

5/8"

4-2ENG

86038450 04/12/07

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Lightning Machine Data LOG Table of Contents HOW to USE this Manual Important Safety Instructions Hazard Intensity Level Hazard Intensity LevelMain Handle Handle Adjustment Lever COMPONENTS/CONTROLSOperating the Machine Machine OperationPRE-RUN Machine Inspection Filter BAGBattery Charging Procedure Battery InformationBattery Maintenance Connection FIRST, Hazardous Sparks MAY ResultTo 6 Month Maintenance MaintenanceWeekly Maintenance Shunt AdjustmentMaintenance Daily Monthly Lubrication & Service ScheduleService Schedule Axle GreasingMachine Troubleshooting Problem Cause SolutionTroubleshooting Machine will not propel

10027110, L20, 10027100, L20T specifications

Windsor 10027110, L20, 10027100, and L20T are advanced heating and cooling systems designed to deliver efficient climate control in various settings. These models incorporate innovative technology and well-considered engineering features that make them stand out in the market.

One of the main features of these units is their energy efficiency. With rising energy costs and increasing environmental concerns, Windsor has focused on creating systems that minimize energy consumption while maximizing performance. The use of high-efficiency compressors and advanced heat exchange technology ensures that energy is used effectively, significantly reducing operating costs.

The Windsor 10027110 model, in particular, features a user-friendly interface that allows for easy temperature adjustments and programming. Users can easily manage their comfort settings, which further enhances the system's efficiency. The systems have the capability for precise temperature control, ensuring that spaces remain comfortable without unnecessary energy expenditure.

In terms of technology, these models are equipped with advanced inverter technology. This technology allows the units to adjust their power output according to the cooling or heating demand. By maintaining optimal performance without the usual energy spikes, inverter technology contributes to lower energy bills and a reduced carbon footprint.

Another notable characteristic of these Windsor systems is their durability and reliability. Built with high-quality materials and engineering processes, these units are designed to withstand the rigors of daily use in various climates. Regular maintenance and servicing can further extend their lifespan, making them a sensible long-term investment for homeowners and businesses alike.

Moreover, the Windsor L20 and L20T models are designed with noise reduction features, ensuring that they operate quietly. This is particularly beneficial in residential areas or in settings where a peaceful environment is paramount.

In conclusion, the Windsor 10027110, L20, 10027100, and L20T heating and cooling systems epitomize a perfect blend of efficiency, technology, and durability. Their user-friendly features and advanced engineering make them ideal solutions for individuals and businesses looking to optimize their climate control solutions while being mindful of energy consumption. These systems not only enhance comfort but also contribute positively to overall cost and environmental impact.
Top Page Image Contents