Windsor SCX264 Controls, Parking Brake Optional, Hour Meter Optional, Brush Pressure Indicator

Page 15

CONTROLS

13.BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries.

The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries.

When the machine is left overnight with less than a full charge, the display may initially indicate a full charge. It will also indicate a full charge if the batteries are disconnected, then reconnected. After a few minutes of operation the meter will give the correct charge level.

14.PARKING BRAKE (OPTIONAL)

Locks front wheels to prevent unintentional movement.

To set parking brake, push down to lock notch.

To release parking brake, push down and over out of the lock down notch.

15.HOUR METER (OPTIONAL)

Records the number of hours the machine has been in operation. This information is useful in determining when to service the machine.

16.BRUSH PRESSURE INDICATOR

The brush pressure indicator corresponds to the amp draw of the scrub brush motors to tell how hard the motors are working. The green zone indicates medium or proper operating brush pressure. The red zone indicates heavy or excessive brush pressure. Operating in the red zone may cause the brush circuit breakers to trip.

CUTTER 24V 86039080 04/17/07

3-8

 

Image 15
Contents SCXC324 WALK BEHIND SCRUBBERSCXC264 10052430MODEL MACHINE DATA LOG/OVERVIEWYOUR DEALER OVERVIEWSAFETY TABLE OF CONTENTSGROUP PARTS LIST HOW TO USE THIS MANUALHOW TO USE THIS MANUAL must always be followed, including the following READ ALL INSTRUCTIONS BEFORE USING THIS MACHINEIMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSWHEN SERVICING MACHINE HAZARD INTENSITY LEVELHAZARD INTENSITY LEVEL FOR SAFETY2% GRADE WARNING SAFETY LABEL LOCATIONSAFETY DECAL 86252530 PRV NO. BATTERY CAUTION PRV NO. CIRCUIT BREAKER DECAL SEE MANUAL PRV NODIMENSION/CAPACITY TECHNICAL SPECIFICATIONSLength SPECIAL NOTESTECHNICAL SPECIFICATIONS MEASURECUTTER 24V 86039080 04/17/07 HOW THE MACHINE WORKS6. Solution Tank 7. Solution Tank Cover COMPONENTS1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head ShroudsCUTTER 24V 86039080 04/17/07 CONTROLS8.Solution Control Knob 9.Vacuum Switch CONTROLS12.SQUEEGEE DEFLECTION ADJUSTMENT KNOBS 8.SOLUTION CONTROL KNOB9.VACUUM SWITCH 11.SQUEEGEE PITCH ADJUSTMENT KNOB15.HOUR METER OPTIONAL 16.BRUSH PRESSURE INDICATORCONTROLS 14.PARKING BRAKE OPTIONALPRE-RUNMACHINE INSPECTION EMERGENCY STOP PROCEDURESFILLING SOLUTION TANK MACHINE OPERATIONTO BEGIN SCRUBBING 3-10NORMAL SCRUBBING MACHINE OPERATIONDOUBLE SCRUB 3-11EMPTYING AND CLEANING TANKS MACHINE OPERATIONWEEKLY MAINTENANCE SERVICE SCHEDULEMAINTENANCE DAILY4.Scrub Brushes 5.Float Shut-Off MAINTENANCE6.Solution Strainer 7.Brush Motor 1.Batteries 2.Squeegee 3.Aqua MizerMAINTENANCE 1. BATTERIESCheck the hydrometer readings against this chart MAINTENANCEB. Battery the battery cover openMAINTENANCE TO REPLACE OR ROTATE REAR SQUEEGEE BLADES ADJUSTING SQUEEGEETO REMOVE SQUEEGEE ASSEMBLY 2. SQUEEGEE BLADESMAINTENANCE TO ADJUST SQUEEGEE PITCHTO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION 3.TO REPLACE AQUA-MIZERSQUEEGEE BLADESUNCOATED FLOORS REPLACING OR INSTALLING SCRUB BRUSHES5. RECOVERY TANK FLOAT SHUT-OFF 4.SCRUB BRUSHES7.BRUSH MOTOR MAINTENANCE6.SOLUTION STRAINER BRUSH MOTOR CARBON BRUSH REPLACEMENT8. TRACTION MOTOR TRACTION MOTOR CARBON BRUSH REPLACEMENT4-10 MAINTENANCE4-11 MAINTENANCENote Place stop in groove MAINTENANCE 12.ACTUATOR SCRUB DECK REMOVAL/REPLACEMENTSCRUB DECK ACTUATOR ADJUSTMENT 4-124-13 MAINTENANCERECOMMENDED GREASING SOLUTION MACHINE TROUBLESHOOTING4-14 PROBLEMSOLUTION 4-15MACHINE TROUBLESHOOTING PROBLEM