Windsor SCXC324 Squeegee Blades, Adjusting Squeegee, To Remove Squeegee Assembly, Maintenance

Page 24
2. SQUEEGEE BLADES

MAINTENANCE

2. SQUEEGEE BLADES

The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use.

The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job. As with the front, each squeegee blade assembly has four wear surfaces for extended service.

Check both the front and rear squeegee blades for damage, wear, and adjustment each day in the pre- run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness.

ADJUSTING SQUEEGEE

Adjusting the squeegee is a two-part process. First, the squeegee assembly must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The knob on the squeegee linkage controls the pitch adjustment. The second adjustment is the deflection. Knobs on each end of the squeegee control this.

ADJUSTING SQUEEGEESQUEEGEE DEFLECTIONTO REMOVE SQUEEGEE ASSEMBLYTO REPLACE OR ROTATE REAR SQUEEGEE BLADESTO REPLACE OR ROTATE FRONT SQUEEGEE BLADEManual backgroundSQUEEGEE DEFLECTIONManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background

CORRECT

NOT ENOUGH

TOO MUCH

SQUEEGEE SIDE VIEW OF

TO REMOVE SQUEEGEE ASSEMBLY

1.With the squeegee in the up position, turn key switch “OFF”.

2.Disconnect vacuum hose from squeegee and loosen both knobs.

3.Pull squeegee assembly rearward from the lifting carrier.

4.Inspect or repair as necessary and reinstall.

TO REPLACE OR ROTATE REAR SQUEEGEE BLADES

1.With the squeegee in the up position, turn key switch “OFF”.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

2.Remove the squeegee assembly from the machine. Unlatch and remove blade retainer strap and remove squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions.

4.Install blade on locating pins of squeegee assembly.

5.Install squeegee retainer strap.

6.Fasten and lock latch, adjust latch only tight enough to take up slack in retaining strap.

TO REPLACE OR ROTATE FRONT SQUEEGEE BLADE

1.With the squeegee in the up position, turn key switch “OFF”.

2.Remove the squeegee from the machine. Loosen three thumbscrews and remove the retainer strap and squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions. When installing the front blade, tighten the center thumbscrew first. Insure that the retainer strap is pressed against the blade before tightening the outer screws.

4-6

CUTTER 24V 86039080 04/17/07

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents WALK BEHIND SCRUBBER SCXC26410052430 SCXC324MACHINE DATA LOG/OVERVIEW YOUR DEALEROVERVIEW MODELTABLE OF CONTENTS GROUP PARTS LISTHOW TO USE THIS MANUAL SAFETYHOW TO USE THIS MANUAL READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONS must always be followed, including the followingHAZARD INTENSITY LEVEL HAZARD INTENSITY LEVELFOR SAFETY WHEN SERVICING MACHINESAFETY LABEL LOCATION SAFETY DECAL 86252530 PRV NO. BATTERY CAUTIONPRV NO. CIRCUIT BREAKER DECAL SEE MANUAL PRV NO 2% GRADE WARNINGTECHNICAL SPECIFICATIONS DIMENSION/CAPACITYSPECIAL NOTES TECHNICAL SPECIFICATIONSMEASURE LengthHOW THE MACHINE WORKS CUTTER 24V 86039080 04/17/07COMPONENTS 1. Control Panel 2. Front Cover 3. Recovery Tank4. Recovery Tank Drain Hose 5. Scrub Head Shrouds 6. Solution Tank 7. Solution Tank CoverCONTROLS CUTTER 24V 86039080 04/17/07CONTROLS 8.Solution Control Knob 9.Vacuum Switch8.SOLUTION CONTROL KNOB 9.VACUUM SWITCH11.SQUEEGEE PITCH ADJUSTMENT KNOB 12.SQUEEGEE DEFLECTION ADJUSTMENT KNOBS16.BRUSH PRESSURE INDICATOR CONTROLS14.PARKING BRAKE OPTIONAL 15.HOUR METER OPTIONALEMERGENCY STOP PROCEDURES FILLING SOLUTION TANKMACHINE OPERATION PRE-RUNMACHINE INSPECTION3-10 NORMAL SCRUBBINGMACHINE OPERATION TO BEGIN SCRUBBING3-11 EMPTYING AND CLEANING TANKSMACHINE OPERATION DOUBLE SCRUBMAINTENANCE SERVICE SCHEDULE MAINTENANCEDAILY WEEKLYMAINTENANCE 6.Solution Strainer 7.Brush Motor1.Batteries 2.Squeegee 3.Aqua Mizer 4.Scrub Brushes 5.Float Shut-Off1. BATTERIES MAINTENANCEMAINTENANCE B. Batterythe battery cover open Check the hydrometer readings against this chartMAINTENANCE ADJUSTING SQUEEGEE TO REMOVE SQUEEGEE ASSEMBLY2. SQUEEGEE BLADES TO REPLACE OR ROTATE REAR SQUEEGEE BLADESTO ADJUST SQUEEGEE PITCH TO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION3.TO REPLACE AQUA-MIZERSQUEEGEE BLADES MAINTENANCEREPLACING OR INSTALLING SCRUB BRUSHES 5. RECOVERY TANK FLOAT SHUT-OFF4.SCRUB BRUSHES UNCOATED FLOORSMAINTENANCE 6.SOLUTION STRAINERBRUSH MOTOR CARBON BRUSH REPLACEMENT 7.BRUSH MOTORTRACTION MOTOR CARBON BRUSH REPLACEMENT 4-10MAINTENANCE 8. TRACTION MOTOR4-11 MAINTENANCENote Place stop in groove 12.ACTUATOR SCRUB DECK REMOVAL/REPLACEMENT SCRUB DECK ACTUATOR ADJUSTMENT4-12 MAINTENANCE4-13 MAINTENANCERECOMMENDED GREASING MACHINE TROUBLESHOOTING 4-14PROBLEM SOLUTION4-15 MACHINE TROUBLESHOOTINGPROBLEM SOLUTION
Top Page Image Contents