Windsor 10080220, CDT7 manual Only Qualified Warning: Maintenance, Personnel Are To, 3/8 9.5mm

Page 20
ONLY QUALIFIED
Wire Terminal

MAINTENANCE

ONLY QUALIFIED

! WARNING: MAINTENANCE

PERSONNEL ARE TO

PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT

1.Turn off all switches and unplug machine.

2.Remove recovery tank.

3.Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame.

4.Locate the vacuum motor wires and disconnect at the connector. Close the solution tank.

5.Remove the (6) screws holding the vacuum motor cover (p/n 27809) to the solution tank.

6.Remove the vacuum motor.

7.Reverse process to install vacuum motor.

Vacuum Motor Carbon Brushes Replacement (Windsor)

 

End Cap

Carbon

WARNING: The green

Brushes

ground wire must be

 

attached for safe operation.

 

See wiring diagram.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

PERSONNEL ARE TO 38 [9.5mm]

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

Vacuum Motor Carbon Brushes Replacement (Ametek)

 

End Cap

Carbon

WARNING: The green

Brushes

ground wire must be

 

attached for safe operation.

 

See wiring diagram.

Note: When replacing carbon brushes loosen wire terminal BEFORE removing screws on bracket.

Wire

Terminal

Note:

Place stop in groove.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

Vacuum Motor Carbon Brushes Replacement (Windsor) 3/8 (9.5mm)

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

4-3

CADET 86038220 03/16/07

Image 20
Contents Operating Instructions MODEL: CDT7CARPET EXTRACTOR 86038220 09/27/07 PRV NO.MACHINE DATA LOG/OVERVIEW MODEL _______________________________________DATE OF PURCHASE __________________________ SERIAL NUMBER ______________________________TABLE OF CONTENTS HOW TO USE THIS MANUALSAFETY OPERATIONSHOW TO USE THIS MANUAL SAVE THESE INSTRUCTIONS SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS HAZARD INTENSITY LEVEL FOR SAFETYWHEN SERVICING MACHINE HAZARD INTENSITY LEVELGROUNDING INSTRUCTIONS GROUNDING INSTRUCTIONSELECTRICAL GENERAL DIMENSIONS/WEIGHT TECHNICAL SPECIFICATIONSPOWER TYPE CONTROLS/COMPONENT LOCATIONS 5.Vacuum Motor Switch. Turns on vacuum motor1 6 2 5 4 86.Recovery Tank Dome 8.Brush Housing 9.Front Lifting Handle10.Cleaning Solution Filter CONTROLS/COMPONENT LOCATIONS1.Solution Intake Cover 2.Vacuum Intake Cover 3.Float Shut-Off 4.Clean-OutOpening 5.Pour SpoutCONTROLS/COMPONENT LOCATIONS 6.Lift HandleFILLING OPERATIONS CADET 86038220 03/16/07RECOVERY TANK SOLUTION TANK FILL LINE FILLING THE CADETOPERATIONS INCORRECTOPERATIONS INTERMITTENT CONTINUOUS1in 25mm CLEANING PROCEDURE1ft 30cm CLEANING PROCEDURE STEPPUMPVACUUM ONON OFF ACCESSORY TOOL USAGE3-10 MAINTENANCE SERVICE SCHEDULE MAINTENANCEDAILY WEEKLYDAILY / REGULAR MAINTENANCE MAINTENANCEPERIODIC MAINTENANCE MAINTENANCE ONLY QUALIFIED WARNING: MAINTENANCEVacuum Motor Carbon Brushes Replacement Windsor Vacuum Motor Carbon Brushes Replacement AmetekTO PERFORM THE FOLLOWING REPAIRS BELT REPLACEMENT MAINTENANCEONLY QUALIFIED WARNING: MAINTENANCE PERSONNEL ARE MAINTENANCE SOLUTION PUMP REPLACEMENTWIRING DIAGRAM 8626845086268830 86266890 PRV NO. 86004480 PRV NO.TROUBLESHOOTING CHART PROBLEMSOLUTION CAUSETHIS PAGE INTENTIONALLY LEFT BLANK MAINTENANCEFRAME ASSEMBLY FRAME ASSEMBLY PART NOBRUSH ASSEMBLY CADET 86038220 03/16/07BRUSH ASSEMBLY PART NOPUMP ASSEMBLY PUMP ASSEMBLY PART NOFROM SERIAL NO: PUMP ASSEMBLYSEE SOLUTION 8 4 10 23PUMP ASSEMBLY PART NOVACUUM SHOE ASSEMBLY CADET 86038220 03/16/075-10 VACUUM SHOE ASSEMBLYCONTROL PANEL ASSEMBLY 5-11PART NO 5-12CONTROL PANEL ASSEMBLY SOLUTION TANK ASSEMBLY 5-13PART NO 5-14SOLUTION TANK ASSEMBLY RECOVERY TANK ASSEMBLY 5-15PART NO 5-16RECOVERY TANK ASSEMBLY SUGGESTED SPARE PARTS 5-17