Wayne-Dalton 341785 Steel Preparation For Painting, Fiberglass Refinishing And Or Finishing

Page 32

Steel Preparation For Painting

Steel (Surface Preparation for Painting)

Wax on the surface must be removed or paint peeling/flaking will result. To remove this wax, it will be necessary to lightly scuff the surface with a fine steel wool pad, saturated with soapy water. A final wipe and rinse should be done with clean water only, to remove any loose particles and any soapy film residue.

Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded with 0000 steel wool or No. 400 sand paper to create a smoother surface. Care must be taken to not expose the substrate under the paint. Once the substrate is exposed, the likelihood for rusting is greatly increased.

If substrate is exposed, it must be treated to prevent rust from forming. Sand the exposed area lightly and paint with a high quality metal primer, specifically intended for galvanized surfaces, to protect the area from corrosion. Allow for drying time on primer can label before applying topcoat.

The surface of the factory-applied finish, that is being painted, must not be too smooth, or the paint will not adhere to it. It is advisable to test in an inconspicuous area, to evaluate adhesion. If poor adhesion is observed, surface preparation for painting the factory-applied finish must be repeated until desired results are achieved. Again, care must be taken to not expose the substrate under the paint.

Steel (Painting)

After surface has been properly prepared, it must be allowed to dry thoroughly, and then coated immediately with premium quality latex house paint. Follow paint label directions explicitly. Oil base or solvent base paints are not recommended. Please note that if substrate is exposed and not properly primed, painting with latex paint may cause accelerated rusting of the steel in the exposed area.

NOTES:

1.This Limited Warranty will be voided if the original finish is painted over, unless Manufacturer’s preparation and painting instructions are followed explicitly.

2.Consult a professional coatings contractor if in doubt about any of the above directions.

3.Follow directions explicitly on the paint container labels for proper applications of coatings and disposal of containers. Pay particular attention to acceptable weather and temperature conditions in which to paint.

Fiberglass Refinishing And Or Finishing

Refinishing

The top coat on factory finished door may require a re-coat after 1-3 years if the surface appears chalky or faded. Reapply a top coat as follows: (Always test on a small area prior to top coating the entire door)

1. Clean surfaces with soap and water, mineral spirits or naptha.

NOTE: Light scuffing of surface may be required using Scotch-Brite™ pads.

2. Apply a commercial brand of exterior grade top coat following the manufacturer instructions.

Finishing

It is recommended that the door be purchased pre-finished due to the size of the door, the required spray equipment and the quality problems that could result. Wayne-Dalton assumes no liability for non-factory finished doors. If finishing is performed, use exterior commercial grade finishing kits approved for use on fiberglass or commercially available exterior grade water based or oil based paint. The customer assumes all liability for the finishing.

32Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Series 4 Section Table of Contents Package Contents Door Section Identification Tools Required LevelTorsion Spring Removal Failure to use approved Winding bars can cause springEnergy to be released Suddenly, resulting in severe Or fatal injuryTorqueMaster Spring Removal Unwind SpringsBracket and Drive Gear Extension Spring Removal Removing the Old DoorPreparing the Opening Attach a SuitableFailure to Securely OpeningFlagangle to Vertical Track InstallationAttaching Quick Install Attaching Fully Adjustable Installing Fully Adjustable Jamb BracketsBottom Bracket Bottom Section Vertical TrackStacking Sections Operator Bracket Top Section Quick Install Flagangle Attaching Horizontal Track toAttaching Horizontal Track to Adjustable Flagangle Top Brackets Fall from Overhead PositionEnd Brackets Center Bearing BracketTorsion Spring Assembly SideNylon Center Bushing For Spring Winding Counterbalance CablesSecuring Door Winding Torsion Springs Rear Support Keep horizontal trackParallel and within 3/4 Maximum of door edge Otherwise door could fall Resulting in severe injury orFor equal tension adjust if CompletedMore than 1 spring turn from Specified amount. If the door stillSide Lock Pull RopeFraming Members Perferated Angle Trolley OperatorHeader Cleaning Your Steel And Fiberglass Garage Door Glass Cleaning InstructionsAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorSteel Preparation For Painting Fiberglass Refinishing And Or FinishingLifetime Limited Warranty Model Thank you for your purchase

341785 specifications

The Wayne-Dalton 341785 is a prominent model in the realm of garage doors, known for its blend of durability, aesthetics, and advanced technology. As a part of Wayne-Dalton's extensive lineup, this model is designed with both functionality and style in mind, making it a popular choice for homeowners seeking to enhance their property's curb appeal.

One of the main features of the Wayne-Dalton 341785 is its construction. It is typically made from high-quality steel, which not only provides exceptional strength but also allows for a range of finishes and colors. This model often comes with a variety of panel designs, allowing homeowners to select a look that best fits their architectural style, whether contemporary or traditional.

Another hallmark of this model is its insulation options. Many versions of the 341785 come equipped with advanced insulation technology, such as polyurethane core insulation, which enhances energy efficiency. This feature is particularly beneficial in regions with extreme temperatures, as it helps maintain a stable climate within the garage, ultimately reducing energy costs and enhancing comfort.

The Wayne-Dalton 341785 also incorporates innovative technology for enhanced security and convenience. Its construction typically includes features such as pinch-resistant joints and tamper-resistant bottom brackets, which provide additional safety for users. The garage door is often compatible with various automatic opening mechanisms, including Wi-Fi-enabled openers, allowing homeowners to monitor and control their garage door from anywhere via a smartphone app.

Aesthetically, the Wayne-Dalton 341785 offers various customizable options. Homeowners can select from different colors, window styles, and decorative hardware, ensuring that the garage door complements their home's exterior. The paint finishes are designed to be weather-resistant, maintaining their appearance and functionality over time.

Maintenance is also straightforward, which is a significant advantage of the Wayne-Dalton 341785. Its durable materials are resistant to fading and rust, requiring minimal upkeep to remain in peak condition. Routine cleaning and inspection can prolong the life of the door and ensure it continues to operate smoothly.

In summary, the Wayne-Dalton 341785 stands out for its robust construction, energy-efficient insulation, advanced security features, and aesthetic versatility. It is an excellent choice for any homeowner looking to combine style and practicality in their garage door solution.
Top Page Image Contents