Quantum/Classicdrive, DoorMaster | Wayne-Dalton 3012, 3014, 3651-372

Step 2: Photoelectric Safety Sensor Wiring Installation For:

Quantum™/Classicdrive™ models: 3012, 3014, 3016, 3018, 3212, 3213, 3214, 3312, 3313, 3314, 3316, 3412, 3414, 3512, 3514.

Uncoil wires from the photoelectric sensors and route wires up the garage walls and along ceiling towards the right side of the opener (see Fig. 1). Route wires behind torque tube and tack wires in place with insulated staples (not supplied).

Take care to run wires in a location where they will not interfere with the operation of the door and do not staple through wire.

IMPORTANT! Keep sender/receiver wires away from moving members.

Connect photoelectric sensors to opener per diagram (Fig. 1). Shorten the wires as necessary and separate the wire ends. Strip about 1/2” of insulation off each wire and attach the solid color wires to the COM terminal and the wires with a black stripe to the OBS terminal. Tighten terminal screws securely, using a small blade screw driver. Be sure to observe polarity. Pull on external wires to test for secure connection. Check that the wires are stapled in place and staples have not cut wire insulation. Reconnect the power to the garage door opener. Proceed to Step 3.

DoorMaster™ models: BDOR-2000 & BIRW-2000

Uncoil wires from the photoelectric sensors and route wires up the garage walls and along door towards the right side of the opener (see Fig. 2). Route wires behind torque tube and tack wires in place with insulated staples (not supplied).

Take care to run wires in a location where they will not interfere with the operation of the door and do not staple through wire.

IMPORTANT! Keep sender/receiver wires away from moving members.

Connect photoelectric sensors to opener per diagram (Fig. 2). Shorten wires as necessary and separate wire ends. Strip about 1/2” of insulation off each wire and attach the solid color wires to the COM terminal and the wires with the black stripe to the OBS terminal. Tighten terminal screws securely, using a small blade screwdriver. Be sure to observe polarity. Pull on external wires to test for secure connection. Check that the wires are stapled in place and staples have not cut wire insulation. Remember to connect telephone type cord for Doormaster™ installation. Once wires are connected, switch the jumper (model BDOR-2000 only) from “Disable” to “Enable” by pulling jumper off pins 2 and 3 and reinstalling jumper on pins 1 and 2.

NOTE: The jumper is set to disable from the factory.

Reconnect the power to the garage door opener. Proceed to Step 3.

Opener

FIG. 1 Wire Routing

Black striped wires

(OBS terminal)

	Sender	Receiver
		wires
	wires

Solid color wire	Solid color wire
(COM terminal)	(COM terminal)

Quantum™/Classicdrive™

FIG. 2 Wire Routing

NOTE: If wires must be lengthened or spliced into prewired installation, use wire nuts or a suitable connector. Pay attention to polarity.

Black striped wire	Sender wires
Black striped wire
(OBS terminal)	Solid color wires
	Solid color wires
	(COM terminal)
	Receiver
Jumper	wires
Jumper
(Model: BDOR-
2000 only)
	Black striped wire
	(OBS terminal)

Right endcap

DoorMaster™

3750-372, 3651-372, 3012, 3014 specifications

Wayne-Dalton is a renowned manufacturer in the garage door industry, offering a wide range of products that cater to various needs. Among their most notable models are the Wayne-Dalton 3014, 3012, 3651-372, and 3750-372 garage doors. Each model brings unique features and technologies designed for durability, aesthetics, and functionality.

The Wayne-Dalton 3014 model is characterized by its exceptional durability and design versatility. It features a steel construction that promotes long-lasting performance, ensuring it can withstand the rigors of everyday use. The door is available in a variety of colors and finishes, allowing homeowners to find the perfect match for their home’s exterior. Additionally, it comes equipped with insulation options that enhance energy efficiency, helping to keep garages comfortable year-round.

The Wayne-Dalton 3012 model emphasizes simplicity and reliability. With a classic design that pairs well with traditional architecture, this model is perfect for homeowners seeking a timeless look. It also features sturdy construction materials that provide added security against potential intrusions. The 3012 model is designed with low maintenance in mind, making it an excellent choice for those who prefer functionality without the hassle.

The 3651-372 model takes performance to the next level. It is constructed with advanced materials that ensure superior strength and insulation properties. This model is particularly beneficial for homes in areas with extreme weather conditions. It also includes modern technology such as smart garage door openers, enabling homeowners to control their garage doors remotely via mobile apps, thus enhancing convenience and security.

Lastly, the Wayne-Dalton 3750-372 model features over-head door technology that enhances its efficiency and reliability. This model incorporates a multi-layer construction approach, combining steel, insulation, and a wood appearance vinyl overlay. This not only offers aesthetic appeal but also provides exceptional insulation, keeping the garage temperature stable. The 3750-372 model can also be customized with various windows and decorative hardware options, allowing homeowners to personalize their garage doors to suit their style.

In summary, Wayne-Dalton's range of models, including the 3014, 3012, 3651-372, and 3750-372, exemplifies quality craftsmanship, advanced technology, and customizable features. These models cater to a variety of preferences, ensuring that there’s a perfect garage door solution for every homeowner.