Fireboy- Xintex, LTD S-2A Tools Required and Hardware, Manual Display Controls / Indicator

Page 2

Tools Required and Hardware

 

• Screw Drivers (Slotted & Phillips)

• Hole Saw 2-1/16” diameter

• Electrical Connector Crimping Tool

• Two 1 Ampere Fuse

With Wire Stripper

• Wire Nuts (#16 Gauge Wire)

• Power Drill

• A Length of #16 Gauge Wire

• Electrical Tape

• Tape Measure and Pencil

• Drill — 3/4 (19.05mm) Diameter

• Crescent Wrench

• Drill — 1/8” (3-17mm) Diameter

• 2 in-Line fuse Holder -

Manual Display Controls / Indicator

A - Solenoid Valve Indicator

B - Sensor #1 Indicator

C - Sensor #2 Indicator

D - Unit Fault Indicator

E- Solenoid Valve On/Off Switch

F- Sensor #1 Test Switch

C - Sensor #2 Test Switch

H - Horn Mute Switch

I - Audible Horn (Internal)

Indicator Definitions

 

 

Solenoid Indicator

 

 

Green

= Solenoid Control on

 

Off

= Solenoid Control off

 

Sensor #1 & #2

 

 

Green

= Sensor active, no fumes detected

Figure 1

Amber

= Sensor failure

 

Red

= Fumes detected! alarm condition

 

Flashing Green

= Sensor warm up period

 

Off

= No sensor detected on power-up

 

Unit Fault

 

 

Off

= Unit Functional

 

Amber

= Fault Detected, horn beeping

 

Display Installation

The S-2A should be mounted in a convenient location, preferably at the source of propane usage (i.e. galley, heater, etc…) where the visual indicators may be readily seen. To install the display, you must first remove the snap-on bezel by inserting a small, flat blade screwdriver into the slot located on either side of the bezel and carefully prying up until the bezel snaps free. (See figure 5)

CAUTION: Do not attempt to remove the four (4) screws, which are now exposed which attach the printed circuit panel to the frame. Doing so will void all warranties.

Next, drill a 2-1 /16” diameter hole into the panel. Slip the instrument through the hole and secure, making sure that you have access to the terminals for solenoid valve connections, positive and negative terminal connections and sensor(s) connections.

Plug in your sensor to connector one and make positive and negative connections for the display and solenoid valve. Finish the installation by fastening to panel with four screws (provided) and snapping bezel back into place.

P/N: 18122

Page 2

Rev. 1.0

 

Rev Date: 9/7/07

 

Image 2
Contents Introduction Components This Kit IncludesDisplay Installation Manual Display Controls / IndicatorIndicator Definitions Tools Required and HardwareSensor Location Sensor InstallationSolenoid Installation Wiring the S-2A Sensor ConnectionOperation Testing Display ModeTerminal Strip Connections Unit Fault Detection Functional Testing of the SensorSensor Fault Detection Nuisance AlarmsSpecifications OptionsOne 1 Year Limited Warranty Rev

S-2A specifications

Fireboy- Xintex, LTD S-2A is a state-of-the-art marine fire suppression system that is specifically designed to protect valuable assets and ensure safety on board vessels. This advanced system utilizes innovative technologies and features to deliver reliable and effective fire protection, making it an essential addition to any marine environment.

One of the standout features of the S-2A system is its ability to automatically detect and suppress fires in enclosed spaces, such as engine compartments, galleys, and other areas prone to fire hazards. This is achieved through the use of advanced thermal detectors that monitor temperature changes and activate the suppression mechanism when necessary, ensuring a swift response to any fire outbreak.

The S-2A system employs a clean agent fire suppression technology, utilizing an environmentally friendly and non-toxic gas, which is safe for both people and the marine environment. This clean agent is designed to quickly extinguish fires without causing damage to equipment or leaving a residue, making it ideal for sensitive areas on the vessel.

Another critical characteristic of the Fireboy S-2A system is its compact design, which allows for easy installation in various types of vessels, including yachts, commercial ships, and recreational boats. The system is engineered to fit into tight spaces while providing optimal fire protection.

The S-2A also features a user-friendly interface that allows for easy monitoring and control. With an integrated alarm system, users are promptly alerted to any issues, enhancing overall safety and promoting quick action and response.

Additional benefits of the Fireboy- Xintex, LTD S-2A include its durability and longevity. The system is constructed with high-quality materials designed to withstand harsh marine conditions, ensuring consistent performance over time.

Overall, the Fireboy- Xintex, LTD S-2A fire suppression system represents a significant advancement in marine safety technology. Its combination of automatic detection, clean agent suppression, compact design, and durable construction makes it a smart choice for anyone looking to enhance the safety of their vessel. Investing in such a system can provide peace of mind and protect both people and property from the devastating impacts of marine fires.