Kidde KN-COB-DP-H) manual Where to Install Your CO Alarm, Where Not to Install Your CO Alarm

Page 7

Part One – Your Kidde CO Alarm

Where to Install Your CO Alarm

Your Kidde CO alarm should be mounted in or near bedrooms and liv- ing areas. It is recommended that you install a Kidde CO alarm on each level of a multi-level home. You may use the number and location of smoke alarms installed in your home according to current building code requirements as a guide to the location of your Kidde CO alarm(s).

WHEN CHOOSING YOUR INSTALLATION LOCATIONS, MAKE SURE YOU CAN HEAR THE ALARM FROM ALL SLEEPING AREAS. IF YOU INSTALL ONLY ONE CARBON MONOXIDE ALARM IN YOUR HOME, INSTALL THE ALARM NEAR BED- ROOMS, NOT IN THE BASEMENT OR FURNACE ROOM.

Seven (7) years after initial power up, this unit will "chirp" every 30 seconds to indicate that it is time to replace the alarm. After seven years the device may no longer detect carbon monoxide accurately and should be replaced immediately. To help identify the date to replace the unit, a label has been affixed to the side of the alarm. Write the "Replace by" date (7 years from power up) in permanent marker on the label.

CAUTION: This CO alarm will only indicate the presence of carbon monoxide at the sensor. Carbon monoxide may be present in other areas.

IMPORTANT: Improper location can affect the sensitive electronic components in this CO alarm. Please see the next section describing where NOT to install this CO alarm.

Where Not to Install Your CO Alarm

To avoid causing damage to the CO alarm, to provide optimum protection, and to prevent unnecessary alarms, follow the direc- tions below where NOT to install this CO alarm:

It is not recommended that you install this CO alarm in garages, kitchens or furnace rooms. Installation in these areas could lead to nuisance alarms, may expose the sensor to substances that could damage or contaminate it, or the alarm may not be heard by persons in other areas of the home, especially if they are sleeping.

In the garage, vehicle exhaust can contain some carbon monoxide. These levels are higher when the engine is first started. CO levels in a garage may not be sufficient to activate the alarm immediately. Within hours of starting a vehicle and backing it out of the garage, the levels present over time can activate the alarm and become a nuisance.

In the kitchen and furnace room, some gas appliances can emit a short burst of carbon monoxide upon startup. This is normal. If your CO alarm is mounted too close to these appliances, it may alarm often and become a nuisance.

Part One – Your Kidde CO Alarm

If you must install a Kidde CO alarm near a cooking or heating appli- ance, install at least 5 feet away from the appliance.

Do not install in excessively dusty, dirty or greasy areas such as kitchens, garages and furnace rooms. Dust, grease or household chemicals can contaminate or coat the alarm’s sensor, causing the unit not to operate properly.

Do not obstruct the vents of the CO alarm. Place the CO alarm where drapes, furniture or other objects do not block the flow of air to the vents.

Do not install in dead air space, such as peaks of vaulted ceilings or gabled roofs, where carbon monoxide may not reach the sensor in time to provide early warning.

Do not install in turbulent air from ceiling fans. Do not install near doors and windows that open to the outside, near fresh air vents, or anywhere that is drafty. Rapid air circulation from fans or fresh air from outside may affect the unit’s alarm response time.

Do not install this CO alarm in a switch- or dimmer-controlled outlet.

Do not install in areas where the temperature is colder than 40˚F (4.4˚C) or hotter than 100˚F (37.8˚C). These areas include uncondi- tioned crawl spaces, attics, porches and garages. Extreme temperatures will affect the sensitivity of the CO alarm.

Do not install CO alarm near deep cell large batteries. Large batteries have emissions that can cause the CO alarm to perform at less than optimal performance.

The following conditions can result in transient CO situations:

Excessive spillage or reverse venting of fuel-burning appliances caused by:

•outdoor ambient conditions, such as wind direction and/or velocity, including high gusts of wind, and insufficient draft in the vent pipes;

•negative pressure differential resulting from the use of exhaust fans;

•simultaneous operation of several fuel-burning appliances competing for limited internal air;

•loose vent pipe connections from fuel-fired appliances;

•obstructions, or unconventional vent pipe designs that can amplify the above situations;

•poorly designed or maintained chimneys and/or vents;

Extended operation of unvented fuel-burning devices (range, oven, fireplace, etc.);

Temperature inversions that can trap exhaust gasses near the ground; and a

Car idling in an open or closed attached garage, or near a home.

11

12

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 900-0107 AlarmTable of Contents Introduction About This User’s GuideSetting up your CO alarm for first time operation Quick Set Up GuideAbout Your CO Alarm Part One Your Kidde CO AlarmDirect plug unit 11, Where to install your CO alarm Kidde’s Unique FeaturesHome Where Not to Install Your CO Alarm Where to Install Your CO AlarmDirect Plug Unit KN-COB-DP-H To installChoose a standard 120V outlet to plug alarm into Normal Operating CharacteristicsMalfunction Signal Group 1 Component Failure Testing the ElectronicsHow to Know If Your Alarm is Malfunctioning If the alarm malfunctionsWhat are the Effects of CO Exposure? How to Care for Your CO AlarmWhat is Carbon Monoxide? Part Two Carbon Monoxide The Silent KillerHome Safety Tips What You Can Do Where Does CO Come From?What Can You do to Protect Your Family? What You Should Not Do Part Three What You Should Know Before the Alarms SoundsClues You Cannot See Part Four What to do When the Alarm Sounds Treatment for CO Poisoning Carbon Monoxide Alarm ProcedureSometimes it’s Difficult to Find the Source of CO in a Home TemperatureTest/Reset Button Part Five Technical InformationHow the CO alarm determines when to alarm Part Six Frequently Asked QuestionsHow much electricity does it take to run the CO alarm? Limited Warranty Kidde / Pyrene Corp

KN-COB-DP-H) specifications

The Kidde KN-COB-DP-H is a state-of-the-art combination carbon monoxide and smoke detector designed to enhance safety in residential and commercial environments. With its advanced features and high-quality construction, it represents a reliable solution for protecting occupants from the dangers of smoke and carbon monoxide exposure.

One of the standout features of the Kidde KN-COB-DP-H is its dual-sensor technology. It utilizes both photoelectric and ionization sensors to detect smoke from various sources. Photoelectric sensors are highly effective at detecting smoldering fires, while ionization sensors are better at recognizing fast-flaming fires. This combination maximizes the unit’s effectiveness in accurately identifying different types of fire threats, providing an early warning system that can save lives.

Moreover, the Kidde KN-COB-DP-H is equipped with a highly sensitive carbon monoxide sensor. Carbon monoxide, a colorless and odorless gas, can pose severe health risks, including poisoning and even death. The detector continuously monitors CO levels in the environment and triggers an alarm if concentrations reach dangerous levels, offering peace of mind to users regarding their safety.

Installation and usability are made easy with the Kidde KN-COB-DP-H. It features a simple mounting process that allows users to quickly set it up in key areas of their homes or businesses, such as bedrooms, hallways, and living rooms. The integrated LCD display provides real-time information about the levels of smoke and carbon monoxide, allowing for easy monitoring and awareness.

The detector also boasts a battery backup feature, ensuring that it remains functional even during power outages. With a life span of many years, the carbon monoxide and smoke detector is a long-term investment in safety. Additionally, it comes equipped with a test/silence button, allowing users to easily verify the functionality of the device and silence false alarms.

Overall, the Kidde KN-COB-DP-H combines innovative technology with user-friendly features, delivering comprehensive protection against both smoke and carbon monoxide hazards. Whether in a home or a workplace, this detector stands as a critical component of any safety plan, promoting a secure environment for all occupants. Investing in such a reliable detector is essential for proactive fire and CO safety awareness.
Top Page Image Contents