Kidde KN-COB-DP-H) manual Testing the Electronics, How to Know If Your Alarm is Malfunctioning

Page 9

Part One – Your Kidde CO Alarm

Testing the Electronics

You should test the alarm once a week, following the directions listed below. If at any time you test the alarm and it does not per- form as described below, have it replaced immediately. Turn to page 16 “How to know if your alarm is malfunctioning” for a description of the characteristics of a malfunctioning alarm and what you should do if a malfunction occurs.

Observe the CO alarm regularly to make sure the green operate light is on, indicating normal operation.

If the green operate light is not on, unplug the CO alarm for three minutes, then plug in again. This will clear the alarm for restart. If the green operate light does not come back on, your CO alarm may be malfunctioning.

To test the CO alarm, press and release the Test/Reset button, within 15 seconds if the CO alarm is operating properly, you will hear 4 quick beeps – followed by 5 seconds of silence – followed by 4 quick beeps. Notice the Red Alarm Light flashes when the unit alarms.

When you test the CO alarm, we advise you to place your finger over the sounder opening in the front of the CO alarm.

Within a minute, the alarm will then return to monitoring for carbon monoxide.

NOTE: Pressing the Test/Reset button tests the functions of the CO alarm’s internal components, circuitry and micro-computer.

YOU DO NOT NEED TO PRESS THE TEST BUTTON TO TAKE A CO READING.

Part One – Your Kidde CO Alarm

How to Know If Your Alarm is Malfunctioning

Your CO alarm performs an internal self-diagnosis every fifteen sec- onds to make sure that it is functioning properly. The CO alarm is designed to alert you in the unusual event of a malfunction.

If the alarm malfunctions.

In the rare event that your alarm malfunctions, it will alert you with one of these signal groups (depending upon the type of malfunction that occurs):

Malfunction Signal Group 1 - Component Failure

– An intermittent “chirping” alarm will sound every 30 seconds.

OR,

Malfunction Signal Group 2 - Microprocessor Failure

–The alarm will sound continuously, and

–The alarm cannot be shut off by pushing the “Test/Reset” button

Unplug the CO alarm immediately and return for warranty exchange (see “Warranty” on page 34).

What to do if you’re not sure...

PLEASE familiarize yourself with the malfunction alert, and do not con- fuse these signals with an alarm. After reading the information above, if you are still unsure whether your CO alarm is operating properly, call the Kidde toll-free consumer hotline at 1 800-581-6742 to do a quick diagnostic check of the alarm over the phone. The customer service representative will be able to assist you and answer your

questions.

If your CO alarm sounder is beeping, and you are not sure if it is a CO alarm or a malfunction alert, reset the alarm, open windows for ventila- tion, turn off fuel-burning appliances (like kerosene or oil heaters, fur- naces, gas ranges, wood-burning stoves, water heaters, or other fossil- fuel burning appliances). For furnaces, you can simply turn down the thermostat to its lowest setting. Open windows and doors for ventila- tion. Then call the Kidde toll-free consumer hotline at 1 800-581-6742 for assistance.

Before you call a qualified technician (such as a licensed heating con- tractor, utility service technician, chimney sweep or fuel provider) to check your residence for CO, remember that you will probably be charged for a service call. Kidde customer service operators are avail- able to answer your questions and assist you in non-emergency situa- tions at no charge.

Never ignore a CO unit’s alarm. A true alarm is an indication of poten- tially dangerous levels of carbon monoxide. CO alarms are designed to alert you to the presence of carbon monoxide before an emergency, before most people would experience symptoms of carbon monoxide poisoning, giving you time to resolve the problem calmly.

15

16

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 900-0107 AlarmTable of Contents Introduction About This User’s GuideSetting up your CO alarm for first time operation Quick Set Up GuidePart One Your Kidde CO Alarm About Your CO AlarmDirect plug unit Kidde’s Unique Features 11, Where to install your CO alarmHome Where Not to Install Your CO Alarm Where to Install Your CO AlarmChoose a standard 120V outlet to plug alarm into To installNormal Operating Characteristics Direct Plug Unit KN-COB-DP-HHow to Know If Your Alarm is Malfunctioning Testing the ElectronicsIf the alarm malfunctions Malfunction Signal Group 1 Component FailureWhat is Carbon Monoxide? How to Care for Your CO AlarmPart Two Carbon Monoxide The Silent Killer What are the Effects of CO Exposure?Where Does CO Come From? Home Safety Tips What You Can DoWhat Can You do to Protect Your Family? Part Three What You Should Know Before the Alarms Sounds What You Should Not DoClues You Cannot See Part Four What to do When the Alarm Sounds Treatment for CO Poisoning Carbon Monoxide Alarm ProcedureTest/Reset Button TemperaturePart Five Technical Information Sometimes it’s Difficult to Find the Source of CO in a HomeHow the CO alarm determines when to alarm Part Six Frequently Asked QuestionsHow much electricity does it take to run the CO alarm? Limited Warranty Kidde / Pyrene Corp

KN-COB-DP-H) specifications

The Kidde KN-COB-DP-H is a state-of-the-art combination carbon monoxide and smoke detector designed to enhance safety in residential and commercial environments. With its advanced features and high-quality construction, it represents a reliable solution for protecting occupants from the dangers of smoke and carbon monoxide exposure.

One of the standout features of the Kidde KN-COB-DP-H is its dual-sensor technology. It utilizes both photoelectric and ionization sensors to detect smoke from various sources. Photoelectric sensors are highly effective at detecting smoldering fires, while ionization sensors are better at recognizing fast-flaming fires. This combination maximizes the unit’s effectiveness in accurately identifying different types of fire threats, providing an early warning system that can save lives.

Moreover, the Kidde KN-COB-DP-H is equipped with a highly sensitive carbon monoxide sensor. Carbon monoxide, a colorless and odorless gas, can pose severe health risks, including poisoning and even death. The detector continuously monitors CO levels in the environment and triggers an alarm if concentrations reach dangerous levels, offering peace of mind to users regarding their safety.

Installation and usability are made easy with the Kidde KN-COB-DP-H. It features a simple mounting process that allows users to quickly set it up in key areas of their homes or businesses, such as bedrooms, hallways, and living rooms. The integrated LCD display provides real-time information about the levels of smoke and carbon monoxide, allowing for easy monitoring and awareness.

The detector also boasts a battery backup feature, ensuring that it remains functional even during power outages. With a life span of many years, the carbon monoxide and smoke detector is a long-term investment in safety. Additionally, it comes equipped with a test/silence button, allowing users to easily verify the functionality of the device and silence false alarms.

Overall, the Kidde KN-COB-DP-H combines innovative technology with user-friendly features, delivering comprehensive protection against both smoke and carbon monoxide hazards. Whether in a home or a workplace, this detector stands as a critical component of any safety plan, promoting a secure environment for all occupants. Investing in such a reliable detector is essential for proactive fire and CO safety awareness.
Top Page Image Contents