A.O. Smith NW 37-670 warranty Installation

Page 6

IMPORTANT

LOCATING THE BOILER

IT IS RECOMMENDED THAT A QUALIFIED SERVICE TECHNICIAN PERFORM THE INITIAL FIRING OF THE BOILER. AT THIS TIME THE USER SHOULD NOT HESITATE TO ASK THE TECHNICIAN ANY QUESTIONS WHICH THEY MAY HAVE IN REGARD TO THE OPERATION AND MAINTENANCE OF THE BOILER.

BEFORE FILLING THE SYSTEM FOR OPERATION the hot water system should be internally cleaned and flushed to remove any contaminants which may have accumulated during installation. See section of this manual titled SYSTEM CLEANING.

RELIEF VALVE

An ASME rated pressure relief valve is furnished with the boiler. A fitting for the relief valve is provided in the top of the boiler. A drain line from the relief valve should terminate near a suitable drain. Do not thread, plug, or cap the end of the drain line.

The pressure setting of the relief valve should not exceed the pressure capacity of any component in the system including the boiler.

HIGH TEMPERATURE DEVICES

Automatic Device

The boiler control circuit contains a high temperature cutoff switch. This device shuts off the heating elements if excessive water temperatures are reached. The high temperature cutoff has an adjustable range of 100° to 240°F and automatically resets on a drop of temperature.

Manual Device

A manual reset high limit will be in the control circuit in addition to the automatic device previously described. The control has an adjustable range of 110° to 290°F and must be manually reset after a drop of temperature.

Reset button is located under the right side panel of the boiler. Disconnect the power before removing the panel to push the button.

INSTALLATION

REQUIRED ABILITY

INSTALLATION OR SERVICE OF THIS BOILER REQUIRES ABILITY EQUIVALENT TO THAT OF A LICENSED TRADESMAN IN THE FIELD INVOLVED. PLUMBING AND ELECTRICAL WORK ARE REQUIRED.

GENERAL

Do not test electrical system before boiler is filled with water, follow START UP procedure in this manual.

The principal components of the boiler are identified in Figure 1. The model and rating plate, see illustration on page 4, provides certain useful information required at installation. Both of these references should be used to identify the boiler and its components.

Water boilers are usually placed in series with the heating system on the outlet side of the circulating pump. The boiler piping should include inlet and outlet water valves to permit maintenance and service work to be performed without disturbing the rest of the system.

Detailed system installation drawings are normally provided by the equipment purchaser or system designer.

For the best installation, the boiler should be located:

1.On a level surface.

Shim the channel type skid base as necessary if leveling is required.

2.Near a floor drain.

The boiler should be located in an area where leakage of the tank or connections will not result in damage to the area adjacent to the boiler or to lower floors of the structure. When such locations cannot be avoided, a suitable drain pan should be installed under the boiler.

The pan should be at least two inches deep, have a minimum length and width of at least two inches greater than the dimensions of the boiler and should be piped to an adequate drain.

The discharge opening of the relief valve should always be piped to an open drain.

3.Suggested clearances from adjacent surfaces are found on a label attached to the control compartment door.

UL minimum clearances:

-24” all sides

-12” top

Allow clearance for hinged control compartment doors.

Elements can be changed with 24” clearance.

4.The boiler may be installed in a confined space if adequate ventilation is provided.

ELECTRICAL

General

Check the boiler model and rating plate information against the characteristics of the branch circuit electrical supply. Do not connect the boiler to an improper source of electricity.

Voltage applied to the boiler should not vary more than + 5% to -10% of the model and rating plate marking for satisfactory operation.

Do not energize the branch circuit for any reason before the boiler is filled with water. Doing so may cause the heating elements to burn out. Such damage is not covered under the terms of the warranty.

The branch circuit is connected to the block through an opening provided on top of the boiler.

The boiler should be connected to a separate, grounded, branch circuit with overcurrent protection and disconnect switch. These are part of the electrical supply system not components of the boiler, as such they are obtained locally. The boiler should be grounded in accordance with national and local codes.

Branch Circuit

The branch circuit wire size should be established through reference to the National Electrical Code or other locally approved source in conjunction with boiler amperage rating. Branch circuit wiring which connects to the boiler terminal block should be temperature rated at 75°C. For convenience, portions of the wire size tables from the Code are reproduced here. It is suggested the electrician size the branch circuit at 125 percent of the boiler rating and further increase wire size as necessary to compensate for voltage drop in long runs. Branch circuit voltage drop should not exceed 3% at the boiler.

6

Image 6
Contents DURA-POWER Models NW 37 Dimensional Data Sizes and Data 45KW Thru 720KWSizes and Data 780KW Thru 3300KW ELECTRICAL/RECOVERY Data Water Boiler SpecificationsModel and Rating Plate Approvals FeaturesForeword GroundingInstallation Boiler Circuits Power CircuitCalculating Amperage/Overcurrent Protection Control CircuitTypical Wiring Diagrams Electrical Configuration TableOperation System CleaningFailure to clean the system may cause FillingMaintenance Checklist System Water TestTank Service and Repair ExpenseClaim Procedure ALL Other Parts

NW 37-670 specifications

A.O. Smith NW 37-670 is a highly regarded water heater that stands out in the residential water heating market. Renowned for its efficiency and reliability, this unit offers homeowners a perfect blend of advanced technology, high performance, and convenience.

One of the main features of the A.O. Smith NW 37-670 is its high recovery rate, which allows for rapid heating of water to meet the demands of a busy household. With a 37-gallon tank capacity, this model can effectively supply hot water for various applications, such as showers, dishwashing, and laundry. The design incorporates a powerful heating element that ensures the water is heated quickly, thus minimizing wait times and improving overall comfort.

Efficiency is a cornerstone of the NW 37-670's design. This water heater features an impressive Energy Factor (EF), which translates to lower energy bills for homeowners. A.O. Smith has integrated advanced insulation materials to maintain water temperature longer, reducing the energy required for reheating. This not only helps in cutting down costs but also promotes eco-friendliness, making it an excellent option for environmentally conscious consumers.

The technology behind the A.O. Smith NW 37-670 includes a state-of-the-art electronic control system. This system continuously monitors the unit's performance and adjusts operations to optimize efficiency. Additionally, the water heater is equipped with a robust diagnostic system that provides real-time feedback, making it easier for homeowners to identify any potential issues before they escalate.

Durability is another defining characteristic of the NW 37-670. Constructed with high-quality materials, including a glass-lined tank for added protection against corrosion, this water heater is designed to last for years with minimal maintenance. The anode rod further enhances its longevity by reducing the potential for rust and increases the lifespan of the unit.

Installation and maintenance are straightforward due to the user-friendly design of the A.O. Smith NW 37-670. It can fit into various spaces, making it a versatile option for both new constructions and replacement projects. A.O. Smith also provides comprehensive support and warranty services, ensuring customer satisfaction and peace of mind.

In summary, the A.O. Smith NW 37-670 is a top-tier water heater that combines efficiency, advanced technology, and durable construction. With its substantial capacity, rapid recovery rate, and modern control features, it is an excellent choice for any home looking for dependable hot water solutions.