Specifications, Installation | White Rodgers 1E30(W), 1F30(W)

SPECIFICATIONS

ELECTRICAL DATA	THERMAL DATA:
Switch Rating: 250 to 750 millivolt DC 0.1 Amps	Temperature Range: 10° to 32°C (50° to 90°F)
	Differential: 1.7°C (3°F)
Switch Action: SPST - Sealed mercury switch

INSTALLATION

SELECT THERMOSTAT LOCATION

Proper location insures that the thermostat will provide a comfortable home temperature. Observe the following general rules when selecting a location:

1.Locate thermostat about 5 ft. above the floor.

2.Install thermostat on a partitioning wall, not on an outside wall.

3.Never expose thermostat to direct light from lamps, sun, fireplaces or any temperature radiating equip- ment.

4.Avoid locations close to windows, adjoining outside walls, or doors that lead outside.

5.Avoid locations close to air registers or in the direct path of air from them.

6.Make sure there are no pipes or duct work in that part of the wall chosen for the thermostat location.

7.Never locate thermostat in a room that is warmer or cooler than the rest of the home, such as the kitchen.

8.Avoid locations with poor air circulation, such as be- hind doors or in alcoves.

9.The living or dining room is normally a good location, provided there is no cooking range or refrigerator on opposite side of wall.

1/2" HOLE FOR

THERMOSTAT WIRE

STOUT CORD WITH 6"

CHAIN ATTACHED

APPROXIMATELY

BASEBOARD5 FEET

STRIP MOLDING

1/4" GUIDE HOLE

FOR SIGHTING

QUARTER ROUND

REMOVED

3/4" HOLE IN FLOOR OF PARTITION

HOOKED WIRE FOR SNAGGING CHAIN

Figure 1. Routing Thermostat Wires

ROUTE WIRES TO LOCATION

1.If an old thermostat is being replaced and is in a satisfactory location, and the wiring appears to be in good condition, use existing wiring. If in doubt, rewire.

2.If a new location is chosen or if this is a new installation, thermostat wire must first be run to the location se- lected. All wiring must conform with local and national electrical codes and ordinances.

NOTE

Because of the small amount of power available on self- generating systems, the gas valve may not operate if there is too much resistance in the circuit. Therefore, choose a location that does not require any more wire than the recommended lengths shown in the Thermostat

Wire Length Table.

THERMOSTAT WIRE LENGTH TABLE

Solid	Max. Length	Max. Combined Length
Wire Sizes	(2-wire cable)	(2 single wires)

No. 18	30 ft.	60 ft.
No. 16	50 ft.	100 ft.
No. 14	80 ft.	160 ft.

3.Probe for obstructions in partition before drilling 1⁄2” hole in wall at selected location. Take up quarter round and drill a small guide hole for sighting (see Fig. 1). From basement, drill 3⁄4” hole in partition floor next to guide hole. In houses without basements, drill 1⁄2” hole through ceiling and into partition from above (see Fig. 1).

4.Through this hole drop a light chain, or 6” chain attached to a strong cord. Snag cord in basement with hooked wire. In houses without basements, drop cord through hole in ceiling and down partitioning; snag cord at the thermostat location.

5.Attach thermostat wire to cord and pull wire through hole in wall so that 6” of wire protrudes.

1E30 (W), 1E30(W), 1F30(W), 1F30 (W) specifications

White Rodgers is renowned for its innovative thermostats and control systems, offering a range of products designed to enhance energy efficiency and comfort in residential and commercial spaces. The models 1F30(W), 1F30(W), 1E30(W), and 1E30(W) exemplify their commitment to quality and advanced technology.

The White Rodgers 1F30 series is a programmable thermostat that benefits homeowners with its user-friendly interface and customizable features. One of its main highlights is its ability to program settings for different times of the day and days of the week, allowing users to adjust temperatures based on their specific schedules. This helps optimize energy consumption, reducing unnecessary heating or cooling when it’s not needed.

Key features of the 1F30 models include a large, easy-to-read display which simplifies temperature adjustments and settings. The models boast intuitive controls that make programming a straightforward process even for users who may not be technologically savvy. Enhanced control means better comfort, providing consistent temperatures throughout the home.

The 1E30 series shares many characteristics with the 1F30 models but is typically aimed at economical and efficient heating systems. With similar programming functionalities, it offers flexibility and efficiency without sacrificing performance. The 1E30 series is particularly noted for its compatibility with various HVAC systems, making it a versatile option for homeowners with diverse heating and cooling needs.

Both the 1F30 and 1E30 series utilize advanced technology such as digital temperature sensing, which ensures accurate readings and reduces fluctuations, creating a more stable indoor environment. Additionally, features like auto-changeover and energy-saving programs help users maintain their desired comfort levels while minimizing energy costs.

In terms of installation, White Rodgers thermostats are designed to be user-friendly, with straightforward wiring and a simple setup process. This means that many homeowners can install the thermostat themselves, saving time and installation costs.

Overall, the White Rodgers 1F30 and 1E30 series bring together ease of use, innovative technology, and energy efficiency. These thermostats stand out for their ability to provide comfort while being mindful of energy consumption. With their modern features, they effectively cater to the needs of today's homeowners who value efficiency, reliability, and user-centric designs. In an era where smart home technology is becoming increasingly important, White Rodgers continues to lead by providing solutions that are not just functional but also seamlessly integrate into daily life.

SPECIFICATIONS

ELECTRICAL DATA

THERMAL DATA: