White Rodgers 1F83-261 specifications Troubleshooting, Symptom Possible Cause Corrective Action

Page 6

TROUBLESHOOTING

Symptom

Possible Cause

Corrective Action

No Heat/No Cool/No Fan

1.

Blown fuse or tripped circuit breaker.

Replace fuse or reset breaker.

(common problems)

2.

Furnace power switch to OFF.

Turn switch to ON.

 

3.

Furnace blower compartment door or

Replace door panel in proper position to engage

 

 

panel loose or not properly installed.

safety interlock or door switch.

No Heat

1.

Pilot light not lit.

Re-light pilot.

 

2.

System Switch not set to Heat.

Set System Switch to Heat and raise setpoint

 

 

 

above room temperature.

 

3.

Loose connection to thermostat or system.

Verify thermostat and system wires are securely

 

 

 

attached.

 

4.

Furnace Lock-Out Condition. Heat may also

Many furnaces have safety devices that shut the

 

 

be intermittent.

system down when a lock-out condition occurs.

 

 

 

If the heat works intermittently contact the furnace

 

 

 

manufacturer or local service person for assistance.

 

5.

Heating System requires service or

Diagonistic: Set System Switch to Heat and raise

 

 

thermostat requires replacement.

the setpoint above room temperature. Within a few

 

 

 

seconds the thermostat should make a soft click

 

 

 

sound. This sound usually indicates the thermostat

 

 

 

is operating properly. If the thermostat does not

 

 

 

click, try the reset operation listed above. If the

 

 

 

thermostat does not click after being reset contact

 

 

 

your heating and cooling service person or place

 

 

 

of purchase for a replacement. If the thermostat

 

 

 

clicks, contact the furnace manufacturer or a

 

 

 

service person to verify the heating system is

 

 

 

operating correctly.

No Cool

1.

System Switch not set to Cool.

Set System Switch to Cool and lower setpoint

 

 

 

below room temperature.

 

2.

Loose connection to thermostat or system.

Verify thermostat and system wires are securely

 

 

 

attached.

 

3.

Cooling System requires service or thermostat

Same procedure as diagnostic for No Heat

 

 

requires replacement.

condition except set the thermostat to Cool and

 

 

 

lower the setpoint below the room temperature.

 

 

 

There may be up to a five minute delay before

 

 

 

the thermostat clicks in Cooling if the compressor

 

 

 

lock-out option is selected in the configuration

 

 

 

menu (Item 6).

Heat, Cool or Fan Runs Constantly.

1.

Fan Switch set to Fan On.

Check each wire connection to verify they are

 

2.

Possible short in wiring.

not shorted or touching together. No bare wire

 

3.

Possible short in thermostat.

should stick out from under terminal screws.

 

4.

Possible short in Heat/Cool/Fan system.

Try resetting the thermostat. If the condition

 

 

 

persists the manufacturer of your system

 

 

 

or service person can instruct you on how

 

 

 

to test the Heat/Cool system for correct

 

 

 

operation. If the system operates correctly,

 

 

 

replace the thermostat.

Furnace Cycles Too Fast or Too Slow

1.

The location of the thermostat and/or the size

Item 2 in the Configuration Menu is the adjustment

(narrow or wide temperature swing)

 

of the Heating System may be influencing the

that controls the cycle rate. If an acceptable cycle

 

 

cycle rate.

rate is not achieved using the FA (Fast) or SL

 

 

 

(Slow) adjustment contact a local service person for

 

 

 

additional suggestions.

Cooling Cycles Too Fast or Too Slow

1.

The location of the thermostat and/or the size

The cycle rate for cooling is fixed and can not be

(narrow or wide temperature swing)

 

of the Cooling System may be influencing the

adjusted. Contact a local service person for

 

 

cycle rate.

suggestions.

Thermostat Setting and Thermometer

1.

Thermostat thermometer setting requires

The thermometer can be adjusted +/- 4 degrees as

Disagree

 

adjustment.

listed in item 7 of the Configuration Menu. No other

 

 

 

adjustment is possible.

Blank Display and/or Keypad Not

1.

Loss of power and dead batteries.

Replace batteries and check heat/cool system for

Responding

2. Voltage Spike or Static Discharge.

proper operation. If a voltage spike or static discharge

 

 

 

occurs use the Reset Operation listed above.

For additional product information, visit www.white-rodgers.com

Page 5 Page 6
Image 6
Page 5 Page 6
Contents Precautions SpecificationsDescription Attach Thermostat Base to Wall InstallationRemove OLD Thermostat Check Thermostat OperationRelay contacts shown are thermostatically operated Configuration Menu OperationTroubleshooting Operating FeaturesSetting the Thermostat Reset OperationTroubleshooting Symptom Possible Cause Corrective Action

1F83-261 specifications

The White Rodgers 1F83-261 is a highly regarded thermostat designed for both residential and light commercial applications. This device combines advanced technology with user-friendly features, providing an efficient solution for temperature control in various settings. It is particularly popular due to its reliability and ease of use, making it a top choice for homeowners and HVAC professionals alike.

One of the standout features of the 1F83-261 is its ability to support multi-stage heating and cooling systems. This allows users to optimize their heating and cooling based on their specific needs, whether that involves a heat pump, gas, or electric systems. The thermostat can manage up to three heating stages and two cooling stages, making it versatile and suitable for a wide range of HVAC configurations.

The 1F83-261 is equipped with a large, easy-to-read digital display that enhances user experience. The screen features a clear layout that allows individuals to quickly view and adjust temperature settings. The backlit display is particularly useful during low-light conditions, ensuring visibility at any time of day or night.

Another key characteristic of this thermostat is its programmable functionality. Users can easily create custom heating and cooling schedules for weekdays and weekends, providing greater comfort and energy efficiency. The programmable feature can help reduce energy consumption by automatically adjusting settings based on occupancy patterns, ultimately leading to cost savings on utility bills.

The thermostat also comes with a user-friendly interface, making it simple for anyone to set up and operate. The intuitive buttons and straightforward menu navigation reduce the learning curve, allowing users to quickly familiarize themselves with the device.

Energy-saving technologies are at the forefront of the 1F83-261 design. It features an energy-saving mode that helps optimize the heating and cooling cycles for maximum efficiency. Additionally, the thermostat is compatible with smart home technologies, enabling integration with various home automation systems for enhanced control and monitoring.

In summary, the White Rodgers 1F83-261 thermostat is a versatile and efficient choice for those seeking to enhance their home's comfort and energy efficiency. With its multi-stage system compatibility, programmable features, intuitive interface, and energy-saving technologies, it stands out as a reliable solution for effective temperature management in modern HVAC systems.
Top Page Image Contents