Desa GP30T GWN20, WMP20, GP30 GN30T Ventilation AIR, Ventilation Air From Inside Building

Page 6

6

AIR FOR COMBUSTION AND VENTILATION

Ventilation Air

AIR FOR COMBUSTION AND VENTILATION

Continued

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.

Ventilation Air From Outdoors

Ventilation

 

Grills

Or

into Adjoining

Remove

Room,

Door into

Option 1

Adjoining

 

Room,

 

Option 3

12"

Ventilation Grills

Into Adjoining Room,

Option 2

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent.

12"

Figure 2 - Ventilation Air from Inside Building

Ventilated

Outlet Attic

Air

Outlet

 

Air

To Attic

 

To

Crawl

Space

Inlet

Air

Inlet Air

 

Ventilated

 

 

Crawl Space

 

 

Figure 3 - Ventilation Air from Outdoors

For..com

107884

Image 6
Contents GWN20T, GWP20T GWN30T, GWP30T What to do if YOU Smell GASTable of Contents Safety InformationLocal Codes Safety Information Product IdentificationProduct Features UnpackingUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating HeaterMounting Bracket Installing Heater to WallAttaching Thermostat Sensing Bulb Removing Front Panel Of HeaterMarking Screw Locations Attaching Mounting Bracket To WallPlacing Heater On Mounting Bracket Mounting Heater to Floor with Optional Floor KIT Installing Bottom Mounting ScrewsMounting Base Feet to Floor Where required by local code Mounting Base Feet to HeaterConnecting to GAS Supply Typical Inlet Pipe DiametersPressure Testing Gas Supply Piping System Pressure Testing Heater Gas ConnectionsChecking GAS Connections Manual Control Models For Your Safety Read Before Lighting Operating HeaterLighting Instructions Shutting Off Heater Manual Lighting ProcedureTo Turn OFF GAS to Appliance Shutting Off Burner Only pilot stays litInspecting Heater Pilot Flame PatternThermostat Control Operation Burner Flame Pattern Cleaning MaintenanceCleaning Burner Pilot AIR Inlet CabinetTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement at Illustrated Parts Breakdown Parts List WMN20 WMP20 Description QTYGWN30T, GWP30T GGN30T, GP30T GWN20T, GWP20T, GWN30T, GWP30T Service Hints SpecificationsReplacement Parts Technical ServiceOwners Registration Form Postage Required Equipment Shutoff Valve GA5010 AccessoriesParts Centrals FAN Kits GA3250TWarranty Information