Desa 10542 Mounting Heater to Floor with Optional Floor KIT, Placing Heater On Mounting Bracket

Page 11

INSTALLATION

Continued

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mount- ing bracket.

Horizontal

 

Slots

Stand-Out Tab

 

Mounting Bracket

 

(attached to wall)

Figure 11 - Mounting Heater Onto

Mounting Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hol- low or solid wall, install wall anchors. Fol- low steps 1 through 4 under Attaching To Wall Anchor Method, page 10.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas con- nections and checking for leaks (see page 14).

Front View

Heater

Wall

 

 

Spacer

Side View

Figure 12 - Installing Bottom Mounting

Screws

MOUNTING HEATER TO FLOOR WITH OPTIONAL FLOOR KIT

Mounting Base Feet to Heater

1.Lay heater cabinet on its back on a table with the heater bottom overhanging the table edge.

2.Align holes in base foot with mounting holes on bottom of cabinet (see Figure 13).

3.Secure base foot to heater using sheet metal screws.

4.Repeat for other side.

Wood

Screw

Base Foot

Sheet Metal Screw

Figure 13 - Installing Base Feet

Mounting Base Feet to Floor (Where required by local code)

1.Remove front panel (see Removing Front Panel of Heater, page 9).

2.Position heater with base feet in desired loca- tion. Mark holes for drilling. Remove heater with base.

113680-01A

www.desatech.com

11

Image 11
Contents What to do if YOU Smell GAS Table of Contents Safety Information Unpacking Product FeaturesLocal Codes Product IdentificationConfined and Unconfined Space AIR for Combustion VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation Air From Inside Building InstallationVentilation AIR Check GAS TypeLocating Heater Installation ItemsInstalling Heater to Wall Attaching To Wall Anchor Method 30,000 Btu/Hr Model20,000 Btu/Hr Model 10,000 Btu/Hr ModelPlacing Heater On Mounting Bracket Installing Bottom Mounting ScrewsMounting Base Feet to Floor Where required by local code Mounting Heater to Floor with Optional Floor KITTypical Inlet Pipe Diameters Connecting to GAS SupplyPropane/LP Natural GasTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Pressure Testing Heater GAS ConnectionsLighting Instructions Manual Control Models For Your Safety Read Before LightingOperating Heater Shutting Off Burner Only pilot stays lit Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off HeaterThermostat Control Operation Burner Flame Pattern Inpecting HeaterPilot Flame Pattern Cabinet Cleaning MaintenanceODS/PILOT and Burner Burner Pilot AIR InletObserved Problem Possible Cause Remedy TroubleshootingReplace burner orifice See Cleaning and Mainte Statement above Gas leak. See Warning10543 Specifications10548 10546 10542/10544 10549 10547 10545Parts Under Warranty Service HintsTechnical Service Service Publications Replacement Parts10,000 BTU/HR Manual Control Models 10542 Illustrated Parts Breakdown10,000 BTU/HR Manual Control Models Parts List19-1 19-2 19-113 10,000, 20,000, and 30,000 BTU/HR Termostat Models Base KIT GA4550 AccessoriesEquipment Shutoff Valve GA5010 FAN Kits GA3210TParts Centrals Limited Warranty VENT-FREE Residential GAS Heaters Warranty InformationKeep this Warranty

10542 specifications

Desa 10542 is a distinctive and innovative community that stands out for its commitment to sustainability and modern living. This urban development exemplifies contemporary design while incorporating green technologies that cater to environmentally conscious residents.

One of the main features of Desa 10542 is its focus on creating a vibrant, inclusive community. The layout of the neighborhood promotes accessibility and connectivity, with wide pedestrian pathways, cycling lanes, and communal spaces designed for social interaction. Parks and green spaces are strategically placed throughout the area, providing residents with lush environments that encourage outdoor activities and foster a sense of community.

In terms of technology, Desa 10542 is at the forefront of smart city initiatives. The integration of smart sensors and IoT devices throughout the community allows for efficient management of resources, such as energy and water. These technologies enable real-time monitoring and analytics, helping to optimize consumption and reduce waste. Homes in Desa 10542 are equipped with smart home systems, allowing residents to control lighting, heating, and security systems remotely via smartphones, enhancing both convenience and safety.

Another characteristic that enhances the appeal of Desa 10542 is its commitment to renewable energy. The community incorporates solar panels on residential rooftops and utilizes wind energy where feasible. This focus on renewable sources not only reduces the carbon footprint of the community but also helps residents save on energy costs.

Desa 10542 also prides itself on its sustainable water management practices. Rainwater harvesting systems and gray water recycling are implemented to minimize water waste, highlighting the community's dedication to resource conservation.

Moreover, the urban design of Desa 10542 includes mixed-use developments that combine residential, commercial, and recreational spaces. This approach creates a dynamic environment where residents can live, work, and play without needing to travel far from home.

In summary, Desa 10542 represents a forward-thinking community that harmoniously blends modern technology with sustainable practices. Its focus on environmental consciousness, smart living, and community connectivity makes it a model for future urban developments, proving that a balance between modernity and nature is not only possible but also desirable.