Desa 10542 installation manual Installing Heater to Wall

Page 9

INSTALLATION

Continued

THERMOSTAT SENSING BULB (Thermostat Models Only)

The thermostat sensing bulb has been placed be- low the heater.

1.Place clamp on thermostat sensing bulb as shown in Figure 5. Clamp is provided in hard- ware package.

2.Snap clamp into upper mounting hole as shown in Figure 5. Mounting hole is located on lower left edge on back of heater. Make sure the ther- mostat sensing bulb is pointing up.

Clamp

Thermostat

Sensing Bulb

Figure 5 - Attaching Thermostat Sensing

Bulb

INSTALLING HEATER TO WALL

Mounting Bracket

Locate mounting bracket in heater carton. Remove mounting bracket from heater carton.

Figure 6 - Mounting Bracket

Removing Front Panel Of Heater

1.Remove the two screws, one on each side of front panel.

2.Pull bottom of front panel up and forward, then out.

3.Remove any remaining packaging materials.

Figure 7 - Removing Front Panel Of

Heater

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes centers are 13 inches apart for the 20,000 and 30,000 Btu/Hr units and 9 inches apart for the 10,000 Bru/Hr units. Attach mounting bracket to wall in one of two ways:

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Ei- ther method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain mini- mum clearances shown in Fig- ure 8, page 10. If you can, provide greater clearances from floor and joining wall.

113680-01A

www.desatech.com

9

Image 9
Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Product FeaturesProduct Identification UnpackingProviding Adequate Ventilation AIR for Combustion VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation AIR InstallationCheck GAS Type Ventilation Air From Inside BuildingLocating Heater Installation ItemsInstalling Heater to Wall 20,000 Btu/Hr Model 30,000 Btu/Hr Model10,000 Btu/Hr Model Attaching To Wall Anchor MethodMounting Base Feet to Floor Where required by local code Installing Bottom Mounting ScrewsMounting Heater to Floor with Optional Floor KIT Placing Heater On Mounting BracketTypical Inlet Pipe Diameters Connecting to GAS SupplyPropane/LP Natural GasTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Pressure Testing Heater GAS ConnectionsManual Control Models For Your Safety Read Before Lighting Operating HeaterLighting Instructions To Turn OFF GAS To Appliance Manual Lighting ProcedureShutting Off Heater Shutting Off Burner Only pilot stays litThermostat Control Operation Inpecting Heater Pilot Flame PatternBurner Flame Pattern ODS/PILOT and Burner Cleaning MaintenanceBurner Pilot AIR Inlet CabinetObserved Problem Possible Cause Remedy TroubleshootingReplace burner orifice See Cleaning and Mainte Statement above Gas leak. See Warning10548 10546 10542/10544 Specifications10549 10547 10545 10543Technical Service Service HintsService Publications Replacement Parts Parts Under Warranty10,000 BTU/HR Manual Control Models 10542 Illustrated Parts Breakdown10,000 BTU/HR Manual Control Models Parts List19-1 19-2 19-113 10,000, 20,000, and 30,000 BTU/HR Termostat Models Equipment Shutoff Valve GA5010 AccessoriesFAN Kits GA3210T Base KIT GA4550Parts Centrals Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Residential GAS Heaters

10542 specifications

Desa 10542 is a distinctive and innovative community that stands out for its commitment to sustainability and modern living. This urban development exemplifies contemporary design while incorporating green technologies that cater to environmentally conscious residents.

One of the main features of Desa 10542 is its focus on creating a vibrant, inclusive community. The layout of the neighborhood promotes accessibility and connectivity, with wide pedestrian pathways, cycling lanes, and communal spaces designed for social interaction. Parks and green spaces are strategically placed throughout the area, providing residents with lush environments that encourage outdoor activities and foster a sense of community.

In terms of technology, Desa 10542 is at the forefront of smart city initiatives. The integration of smart sensors and IoT devices throughout the community allows for efficient management of resources, such as energy and water. These technologies enable real-time monitoring and analytics, helping to optimize consumption and reduce waste. Homes in Desa 10542 are equipped with smart home systems, allowing residents to control lighting, heating, and security systems remotely via smartphones, enhancing both convenience and safety.

Another characteristic that enhances the appeal of Desa 10542 is its commitment to renewable energy. The community incorporates solar panels on residential rooftops and utilizes wind energy where feasible. This focus on renewable sources not only reduces the carbon footprint of the community but also helps residents save on energy costs.

Desa 10542 also prides itself on its sustainable water management practices. Rainwater harvesting systems and gray water recycling are implemented to minimize water waste, highlighting the community's dedication to resource conservation.

Moreover, the urban design of Desa 10542 includes mixed-use developments that combine residential, commercial, and recreational spaces. This approach creates a dynamic environment where residents can live, work, and play without needing to travel far from home.

In summary, Desa 10542 represents a forward-thinking community that harmoniously blends modern technology with sustainable practices. Its focus on environmental consciousness, smart living, and community connectivity makes it a model for future urban developments, proving that a balance between modernity and nature is not only possible but also desirable.