Securing Hearth Base to Floor

OWNER’S MANUAL

INSTALLATION

Continued

1.Position hearth base in desired location. Mark holes for drilling (see Figure 18). Remove hearth base.

2.For carpeted floor, make a small cut with a sharp knife at marked loca- tions before drilling. If securing to a wood floor, drill a 3/4" deep hole using a 1/8" diameter drill bit. Do not use anchors in wood floors. If securing to a concrete floor, drill a 1 3/8" deep hole using a 1/4" diameter concrete drill bit. Completely insert anchors into each hole.

3.Mount heater to hearth base following steps under Mounting Heater to Op- tional Hearth Base, below. After mounting heater, position heater and hearth base over drilled holes. With slotted screwdriver, secure hearth base to floor with four wood screws.

Mounting Heater to Optional Hearth Base

1.Lay heater on its back on a table with the bottom of heater overhanging the edge of the table.

2.Remove 2 shipping screws in bottom of heater. Discard shipping screws.

3.Line up mounting holes on top of hearth base with holes in bottom of heater (see Figure 18).

4.Using a Phillips screwdriver, secure hearth base to heater with four sheet metal screws (see Figure 18).

5.Stand heater up on base.

6.Place hearth insert in hearth base as shown in Figure 19.

7.Assemble brass trim (see steps 1 through 7 under Assembling and At- taching Brass Trim, page 5).

8.Slide base trim on heater base. Attach brass trim to base with two brass screws included as shown in Figure 19.

Shipping Bottom of Heater Base Screw

Mounting Holes

Holes for Securing	Sheet Metal Screw
Heater to Floor

Figure 18 - Attaching Heater to Hearth Base

Laminate

Sheet

Hearth

Insert

Screw

Brass Base

Trim

Figure 19 - Placing Hearth Insert on Heater Base and Attaching Brass Base Trim

C. MOUNTING HEATER WITH OPTIONAL HEARTH BASE (IF APPLICABLE) TO OPTIONAL MANTEL

See instructions included with mantel kit.

Assembling Mantel

IMPORTANT: Only use the optional man- tels specified in this manual. See Accesso- ries, page 21 for proper mantel kits. This heater is only approved for use with models GMF800 series / GMU801 series, GM900F series / GM901U series, GM700F/GM701U series, GMC22F/GMC23U/GMC24U se- ries, GMC32F/GMC33U series, GMC34F/ GMC35U series, and GMC26F/GMC27U/ GMC28F series mantel kits. Using any other mantel will void the A.G.A. approval for this heater. Do not use models GMF800/ GMU801 series, GM900F/GM901U series, GM700F/GM701U series, GMC22F/ GMC23U/GMC24U series, GMC32F/ GMC33U series, GMC26F/GMC27U/ GMC28F series and GMC34F/GMC35U series mantels with any other product. If the metal base is required with your mantel, the heater must be mounted on the base first.

Continued

104779

RFN28TD specifications

Desa Tech RFN28TD is a notable advancement in the realm of remote communication technology, specifically designed to meet the increasing demands of modern industries. This radio frequency network device is tailored to enable seamless communication across various platforms, making it indispensable for organizations looking to enhance their operational efficiency.

One of the key features of the RFN28TD is its robust dual-band functionality, which operates across both the 2.4 GHz and 5 GHz frequency bands. This dual-band capability allows the device to adapt to varying environmental conditions, providing users with a stable and reliable connection even in congested areas. The RFN28TD is equipped with advanced adaptive transmission technology, ensuring optimal performance and quality of service by dynamically selecting the best frequency for transmission.

Another significant characteristic of the RFN28TD is its long-range communication capability. With an impressive range of up to several kilometers under optimal conditions, this device is ideal for applications requiring extensive coverage, such as industrial automation, smart cities, and agricultural monitoring. The built-in high-gain antennas further enhance its reach, allowing for improved signal penetration through obstacles.

The RFN28TD is also designed with security in mind. It incorporates advanced encryption protocols, ensuring that data transmitted over the network is secure and protected from unauthorized access. This is particularly crucial for businesses handling sensitive information, as data breaches can lead to severe consequences.

In terms of ease of use, the device offers a user-friendly interface that simplifies the setup and management processes. Its plug-and-play design allows for quick installation, making it accessible even for users with minimal technical expertise. Additionally, the RFN28TD supports a wide range of connectivity options, including Ethernet and Wi-Fi, further enhancing its versatility.

Energy efficiency is another highlight of the RFN28TD, as it operates on lower power consumption compared to traditional communication devices. This not only reduces operational costs but also contributes to a greener, more sustainable approach to technology.

In conclusion, the Desa Tech RFN28TD is a powerful and versatile communication device that combines advanced features, long-range capabilities, robust security, and energy efficiency. Its adaptability to various applications makes it an essential tool for businesses and industries aiming to leverage the benefits of modern communication technologies.