Appliance Data, Unpacking the Appliance, I2H I3P

INTRODUCTION

Thank you for choosing this burley product. All of our products carry a CE mark which is awarded by an independent test house (notified body) and shows the fires have been type tested to meet the essential requirements of the European Gas Appliance Directive and the appropriate British Standards.

This is a highly efficient Flueless Inset Live Fuel Effect Appliance. The burner system is very clean burning and a catalyst cleans the combustion products even further.

A thermostat in the burner control system adjusts heat output to maintain a room temperature, which can easily be set by the user. The appliance is operated via a battery powered remote control system. There is also a separate control to adjust the flame effect as required. Please demonstrate its operation to the customer before leaving.

An oxygen depletion sensing pilot light is also fitted and will sense any significant oxygen depletion in the room and shut the fire down safely.

1.APPLIANCE DATA

Refer to the appliance data badge (affixed behind controls door) ENSURE THAT THE LOCAL CONDITIONS OF USE CORRESPOND TO THE INFORMATION ON THE DATA BADGE.

		Natural Gas G20	LPG (Propane) G31
Category		I2H	I3P
Supply Pressure		20mBar	37mBar
Inlet Pressure		20mBar*	37mBar*
Burner Pressure	(High)	9.4mBar	35.5mBar
	(Low)	2.2mBar	8mBar
Heat Input (Net)	(High)	3.5kW	3.5kW	(250g/h)
	(Low)	1.7kW	1.7kW	(120g/h)
Inlet Connection		8mm Compression	8mm Compression
Injector		stereo 185	stereo 95

*The inlet pressure must be within +/- 1mBar of specification with all gas appliances in the house switched on and also with just the Burley heater operating. If outside of this tolerance the fault is most likely to be in the installation pipe work or service governor at the meter. If the problem is the meter governor, this is the property of the gas service provider (such as Transco / National Grid 0800 111999 or Bord Gais) and they should be called to rectify this. The fire will not operate correctly if the pressures are incorrect.

2.UNPACKING THE APPLIANCE

2.1Carefully examine the carton for damage before unpacking. If it is obviously damaged, consult the supplier as to whether to proceed with the installation.

2.2Make sure the carton is stood upright and open the top. Remove the cardboard top fitting and place to one side; this box can be used as a hearth protector when installing the fire.

2.3Remove the fittings boxes contained within and open them and check the condition of the contents. Remove the fire and examine its general condition, paying particular attention to the frame, the glass front and fire box flanges.

2.4If satisfied by the general condition, place the decorative components to one side and proceed with the installation. If in any doubt, seek advice from the supplier. Read these instructions fully before proceeding even if you have fitted this model before.

G4121 mk2 specifications

The Burley G4121 mk2 is a cutting-edge bicycle that exemplifies the fusion of performance, comfort, and durability. Built for both novice and experienced riders, this model reflects Burley's commitment to engineering excellence and innovative design.

One of the standout features of the G4121 mk2 is its lightweight aluminum frame. This construction material not only contributes to the bike's overall agility but also enhances its resistance to corrosion and wear. The geometry of the frame is meticulously designed to provide an optimal balance between speed and stability, making it ideal for various terrains, from urban roads to light trails.

Equipped with a Shimano 21-speed transmission, the Burley G4121 mk2 offers riders the versatility needed to tackle steep climbs or swift descents effortlessly. The smooth shifting mechanism ensures precise gear changes, allowing riders to maintain momentum without sacrificing control. This model also features a reliable braking system, incorporating both front and rear disc brakes, which provide excellent stopping power and responsiveness, crucial for navigating through dynamic environments.

Comfort is a key aspect of the G4121 mk2. The bike is fitted with an ergonomic saddle and adjustable handlebars, accommodating different riding styles and preferences. Puncture-resistant tires enhance safety and offer peace of mind during longer rides, minimizing the risk of being stranded due to flat tires.

Incorporating advanced technologies, the G4121 mk2 boasts a lightweight, adjustable suspension system. This feature absorbs shocks from uneven surfaces, ensuring a smoother ride and reducing fatigue during extended journeys. Additionally, the bike’s reflective elements improve visibility in low-light conditions, enhancing safety for commuters and weekend adventurers alike.

The Burley G4121 mk2 also considers practicality with its integrated mounts for racks and fenders, allowing riders to customize their bike for commuting or touring experiences.

In conclusion, the Burley G4121 mk2 stands out not just for its performance characteristics but also for its thoughtful design aimed at enhancing rider experience. It is a versatile bicycle that successfully caters to both form and function, making it a popular choice among cycling enthusiasts.