BRK electronic SC7010B user manual Locking Features, To Lock the Battery Compartment

Page 5

LOCKING FEATURES

The locking features are designed to discourage unauthorized removal of the batteries or Alarm. It is not necessary to activate the locks in single-family households where unauthorized battery or Alarm removal is not a concern.

These Alarms have two separate locking features: one to lock the battery compartment, and the other to lock the Alarm to the mounting bracket. You can choose to use either feature independently, or use them both.

Tools you will need: Needle-nose pliers • Standard Flathead screwdriver.

Both locking features use locking pins, which are molded into the mounting bracket. Using needle-nose pliers, remove one or both pins from the mounting bracket, depending on how many locking features you want to use.

To permanently remove either lock, insert a flathead screwdriver between the locking pin and the lock, and pry the pin out of the lock.

TO LOCK THE BATTERY COMPARTMENT

Do not lock the battery compartment until you have installed the battery and tested the battery back-up.

1. Push and hold Test/Silence button until the alarm sounds.

If the unit does not alarm during testing, DO NOT lock the battery compartment! Install a new battery and test again. If the Alarm still does not alarm, replace it immediately.

2.Using needle-nose pliers, detach one locking pin from the mounting bracket.

3.Push the locking pin through the hole near the battery drawer on the back of the Alarm.

TO UNLOCK THE BATTERY COMPARTMENT

Once the Alarm is installed, you must disconnect it from the AC power before unlocking the battery compartment.

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the Alarm is installed before removing it from the mounting bracket. Failure to turn off the power first may result in serious electrical shock, injury or death.

Always discharge the branch circuit before servicing an AC or AC/DC Alarm. First, turn off the AC power at the circuit breaker or fuse box. Next, remove the battery from Alarms with battery back-up. Finally, press and hold the Test/Silence button for 5-10 seconds to discharge the branch circuit.

1. Remove the Alarm from the mounting bracket. If the unit is locked to the bracket, see the section “To Unlock the Mounting Bracket.”

2. Disconnect the power connector by gently prying it away from the back of the Alarm.

3. Insert a flathead screwdriver under the head of the locking pin, and gently pry it out of the battery compartment lock. (If you plan to relock the battery compartment, save the locking pin.)

4.To relock the battery compartment, close the battery door and reinsert locking pin in lock.

5.Reconnect the power connector to the back of the Alarm, reattach the Smoke Alarm to the mounting bracket, and restore the power.

When replacing the batteries, always test the Alarm before relocking the battery compartment.

TO LOCK THE MOUNTING BRACKET

1.Using needle-nose pliers, detach one locking pin from mounting bracket.

2. Insert the locking pin into the lock located opposite from the battery drawer as shown in the diagram.

3.When you attach the Alarm to the mounting bracket, the locking pin’s head will fit into a notch on the bracket.

TO UNLOCK THE MOUNTING BRACKET

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the Alarm is installed before removing it from the mounting bracket. Failure to turn off the power first may result in serious electrical shock, injury or death.

Always discharge the branch circuit before servicing an AC or AC/DC Alarm. First, turn off the AC power at the circuit breaker or fuse box. Next, remove the battery from Alarms with battery back-up. Finally, press and hold the Test/Silence button for 5-10 seconds to discharge the branch circuit.

1. Insert a flathead screwdriver between the mounting bracket pin and the mounting bracket.

2. Pry the Alarm away from the bracket by turning both the screwdriver and the Alarm counterclockwise (left) at the same time.

5

Image 5
Contents Introduction Table of ContentsUSER’S Manual Where to Install this Alarm InstallationWhere this Alarm should not be Installed Recommended PlacementParts of this Alarm HOW to Install this SMOKE/CO AlarmPower Connector Mounting BracketInterconnected Units only Follow These Installation StepsSTAND-ALONE Alarm only To Lock the Battery Compartment Locking FeaturesTo Unlock the Battery Compartment To Lock the Mounting BracketRegular Maintenance Weekly TestingIf Your SMOKE/CO Alarm Sounds What YOU will see and Hear with this AlarmIf the Smoke Alarm Sounds If the CO Alarm SoundsUsing the Silence Features Silencing the LOW Battery WarningHOW can I Protect MY Family from CO POISONING? What YOU Need to Know about CORegulatory Information for Smoke Alarms Regulatory Information for SMOKE/CO AlarmsRegulatory Information for CO Alarms Special Compliance Considerations General Limitations of SMOKE/CO AlarmsAbout Smoke Alarms Limited Warranty Troubleshooting Guide