Hearth and Home Technologies GBST4336I, GBFL4136I Electrical Information, Wiring Requirements

Page 29

12 Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric

Code CSA C22.1.

•Wire the appliance junction box to 110-120 VAC. This is required for use of optional accessories (standing pilot ignition) or proper operation of the appliance (Intellifire ignition).

•A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

•Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 110V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

B. Intellifire Ignition System Wiring

•Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

•Refer to Figure 12.1, Intellifire Pilot Ignition (IPI) Wiring Diagram.

•This appliance is equipped with an Intellifire control valve which operates on a 3 volt system.

•Plug the 3-volt AC transformer into the appliance junction box to supply power to the unit OR install two D cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur.

C. Optional Accessories Requirements

•This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

Note: A blower kit is not approved for this appliance.

Heatilator • GBST4336I, GBFL4136I • 2135-900 Rev. D • 11/08

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents What to do if you smell gas ModelHomeowner Reference Information CongratulationsUser Guide Table of ContentsReference Materials Appliance SetupTroubleshooting CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyClear Space Decorative Doors and FrontsFinal inspection by Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianLogs FireboxTypical Appliance System Getting StartedInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Negative Pressure Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseGBFL4136I GBFL4136I Mantel Projection Mantel and Wall Projections GBST4336I Mantel ProjectionCombustible Mantel Legs or Wall Projections Fireplace OpeningVent Termination Minimum Clearances Termination LocationsVent Guidelines Vent Information and DiagramsVent System Configuration Models Pipe SizePipe Clearances to Combustibles Vent Clearances and FramingWall and Ceiling Penetration Framing Vertical Penetration FramingGas and Electrical Connections Installing Outside Air Kit Damper Assem- blyAppliance Preparation Proper Positioning, Leveling And Securing Securing and Leveling the ApplianceAssembly of Vent Sections Installing Vent PipeInstall Attic Insulation Shield Attaching Vent to FireboxFuel Conversion Gas InformationGas Pressure Gas ConnectionIntellifire Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationElectrical Service and Repair Junction Box Detail Junction Box InstallationSplatter Guard To install the Splatter GuardFinishing To Remove the Splatter Guard To Close the Lower Access Panel12 Minimum Vertical and Maximum Horizontal GBFL4136I Pier Mantel ProjectionFacing Material 17 Noncombustible Facing DiagramAppliance Setup Models GDST4336I, GDFL4136I, GDCL4136I, GBST4336I, GBFL4136I Install the Log AssemblyModel GDCR4136I Placement of Log #2Burner Air Shutter Settings Install Trim Kits and SurroundsAir Shutter Setting Intellifire Ignition System TroubleshootingSymptom Possible Cause Corrective Action Intellifire Ignition System Reference Materials Appliance Dimension DiagramFront View Part number list on following Log Set AssemblyService Parts At Depot GBST4336IGBFL4136I Stocked Service Parts ListGBST4336I, GBFL4136I IPI Valve AssemblyContact Information
Related manuals
Manual 49 pages 62.21 Kb

GBST4336I, GBFL4136I specifications

Hearth and Home Technologies has made significant strides in the realm of contemporary heating solutions with their innovative products, the GBST4336I and GBFL4136I fireplace inserts. These models exemplify a blend of cutting-edge technology, aesthetic design, and user-friendly features aimed at enhancing the home heating experience.

The GBST4336I, known for its striking design and powerful performance, offers a modern solution to traditional heating methods. This model showcases a large viewing area, providing an expansive glimpse into the mesmerizing flames. Its efficient combustion system allows for exceptional heat output while minimizing emissions, making it an eco-friendly choice for homeowners. The insert is designed to fit seamlessly into most existing fireplace spaces, significantly enhancing the ambiance and warmth of any living area.

On the other hand, the GBFL4136I model is tailored for those seeking a more traditional wood-burning experience combined with modern efficiency. This insert features an impressive firebox capacity, allowing users to load more wood for longer burn times. The innovative air wash system keeps the glass clean, ensuring an unobstructed view of the fire. Additionally, the optional blower enhances heat circulation throughout the room, making it perfect for large spaces.

Both models are equipped with advanced technologies that contribute to their reliability and performance. The adjustable burn settings allow users to regulate heat output based on their specific needs, making these inserts versatile for different settings. Furthermore, they include the latest in safety features such as automatic shut-off capabilities, ensuring peace of mind while enjoying the warmth of the fire.

Aesthetically, both the GBST4336I and GBFL4136I come with customizable options, allowing homeowners to choose from various trim and finish choices to fit their home décor. The modern design elements, combined with classic fireplace features, ensure that these inserts not only heat the space but also serve as a stunning focal point in any room.

In summary, Hearth and Home Technologies' GBST4336I and GBFL4136I fireplace inserts stand out for their exceptional design, advanced technology, and practicality. They cater to the needs of modern homeowners by offering efficient heating solutions while maintaining an inviting and stylish atmosphere. With features that prioritize performance and safety, these inserts are an excellent choice for anyone looking to enhance their living space with the warmth and beauty of a fire.
Top Page Image Contents