Hearth and Home Technologies BIR50-B owner manual Install Back Molded Brick Panel-Herring- bone

Page 37

D. Install Back Molded Brick Panel-Herring- bone

•Remove Screen Rods

•Remove Smokeshield

•Refer to Figure 11.2.

•Set the grate brackets in place, 26.5 in. (673 mm) center to center.

•Install the back panel. Center from side to side.

•Install two Z-brackets in the mortar lines across the top. Tighten these and all previously installed brackets.

E. Install Side Molded Brick Panel-Herring- bone

•If a gas line is to be installed, remove the knockouts in the inner firebox and in the outer shell on the side of your choice. Refer to dimension drawings for location of knockouts and Section 13.A. for gas provisions.

•Install side panel, tapered edge to the front. Align the front edge with the front of the column (or butted to the surround if installed).

•Install two Z-brackets in the mortar lines across the top. Tighten these and all previously installed brackets.

•Install second side panel following the steps above.

•Replace the smokeshield.

Back Herringbone Refractory

LH Herringbone Refractory

Refractory clip

Hearth

Figure 11.2 Herringbone Molded Brick Panel

Heatilator • Birmingham BIR50-B • 4059-682C• 8/12

37

Image 37

Contents Fire Risk Hot screen/mesh and glass doors will cause burnsGrate Listing Label Information/LocationNumber Heatilator Birmingham BIR50-B 4059-682C 8/12Installer Guide Table of ContentsUser Guide Limited Lifetime Warranty WarrantyWarranty Conditions Appliance Certification Listing and Code ApprovalsNon-combustible Materials Combustible MaterialsYour Fireplace Operating InstructionsStarting a Fire Seasoned WoodGrate FirescreenVented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear SpaceHardwood vs Softwood Wood FuelChimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Check Firebox Molded Brick Panel Glass CleaningInspect Grate Frequency As desiredStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedDraft Design and Installation ConsiderationsNegative Pressure Windward Locating your Fireplace & ChimneyTypical Fireplace Components Tools and Supplies Needed Inspect Fireplace and ComponentsSelect Fireplace Location Framing & ClearancesModel # Air Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsThings to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth StripsYES Install Outside Air KitChimney Requirements Chimney AssemblyEffective Install Firestop Installation NotesFrame Openings Cut Roof OpeningAssemble Chimney Sections Using Offsets/ReturnsSupplementary Support & Stabilizer Offset Elbow InstallationInstall Roof Radiation Shields Install Attic Insulation ShieldAttach Flashing Field-Constructed Chase Top Flashing Finish Top Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsShroud Requirements Shrouds House Style Shroud House Style Shroud Minimum DimensionsPyramid Style Shroud Arch / Mailbox Style ShroudInstall Hearth Molded Brick Panel Installation of Molded Brick PanelInstall Back Molded Brick Panel-Traditional Install Side Molded Brick Panel-TraditionalInstall Side Molded Brick Panel-Herring- bone Install Back Molded Brick Panel-Herring- boneInstall Mortar Optional Install ScreensHearth Extension Finishing= 1/k x inches of thickness Raised Hearth Extension Framing Decorative Facing Finishing MaterialStandoffs Combustible MantelFlush Front Gas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1Reference Materials Fireplace DimensionsRequired/shipped separately Chimney ComponentsStocked Service PartsAt Depot 50 in. Woodburning FireplaceTraditional Refractory Traditional RefractoryHerringbone Refractory This page intentionally left blank Contact Information