Sears 390.30479 Safety / Installation, Additional Installation, Materials Purchase Separately

SAFETY / INSTALLATION

4.Never rim pump dry. To do so can damage internal parts, overheat the pump (which can cause burns to peo- ple handling or servicing the pump), and will void the warranty_.

5.DO NOT attempt to oil the pump motor. A special oil has been put into the motor housing at the factory; use of any

other oll will void the warranty and could damage the pump.

6.This pump is recommended for use in permanent instal-

lations only. This pump has not been invenstigated for use in swimming pool areas.

7.Know the pump application, limitations, and potential hazards. Not for use with salt water or brine.

[_'WARNING]Do not use in explosive atmospheres.

Pump water only with this pump. Failure to follow

this warning can result in personal injury and!or

property damage.

8.Release aU pressure within the system before servicing any component.

9.Drain water from the system before servicing.

10.Secure the discharge line before starting the pump. An un-

secured discharge line will whip, possible causing per- sonal injury and/or property damage.

11.Periodically inspect pump and system components. Perform

routine maintenance as required (See MAINTENANCE).

12.Provide a means of pressure relief for pumps whose dis- charge line can be shut-off or obstructed.

13.Personal Safety:

a:Wear safety glasses at all times when working with pumps.

b. Keep work area clean, uncluttered and properly lighted - replace all unused tools and equipment.

c. Keep visitors at a safe distance from the work area.

d. Make workshop child-proof - with padlocks, master

switches, and by removing starter keys.

14.This equipment is ordy for use on 115 volt (single phase)

and is equipped with an approved 3-conductor cord and

3-prong, grounding-type plug.

[_WARNING]To

reduce

the risk

of

electric

shock,

pull

plug

before

servicing.

This

pump

has

not

been

investigated

for

use

in

swimming

pool

areas.

This

pump

is

supplied

with

a

grounding

conductor

and

grounding-type

attachment

plug.

Be certain

that

it

is connected

only to a

properly

grounded

ground-

ing-type

receptacle.

Where

a

2-prong

wall

receptacle

is

encountered,

it

must

be replaced

with

a properly

grounded

3-prong

receptacle

installed

in

accordance

with

the

National

Electrical

Code

and

local

codes

and

ordinances.

15.Protect

electrical

cord

from

sharp

objects,

hot

surfaces,

oil,

and

chemicals.

Avoid

kinking the

cord.

Replace

or

re-

pair damaged or worn cords immediately.

16.Do not handle a pump or pump motor with wet hands or when standing on a wet or damp surface, or in water.

1

of

electric

shock.

If

your

basement

IA WARNING jR is k

has

water

or

moisture

on

the

floor,

do

not

walk

on

wet

area

until

all

power

has

been

turned

off.

If

shut-off

box

is in

basement,

call

the

electric

company

to shut-

off

service

to

the

house,

or

call

your

local

fire

depart-

ment

for

instructions.

Remove

pump

and

repair

or

replace.

Failure

to

follow

this

warning

can

result

in

fatal

electrical

shock.

ADDITIONAL INSTALLATION

MATERIALS (Purchase Separately)

Sttmp Pump Hose Kit, SEARS Stock No. 27909, containing

24' (7.3M) of 1-1/4" flexible plastic pipe, 1-1/4" plastic

adapter and stainless steel clamp. We recommend a Check Valve, SEARS Stock No. 2789 or 2792.

THE SUMP

Locate sump at lowest place in basement or drained area. Floor drains or drain tiles can also be tiled into sump. Minimum sump size is 12" (305ram) in diameter by 24" (610mm) deep for model 390.305001 and 10" (254mm) in diameter by 20" deep (508ram) for models 390.304790 and

390.305790. Periodically inspect pump, system com- ponents, and sump for debris and foreign objects. Keep sump free from all refuse. Perform routine maintenance as required. Use a sump cover to exclude refuse from sump.

Consult local code for cover specifications.

Grounded Outlet-_[_
Sump Cover	Basement Floor
-..,	-..,
\\\_.\\ \\-_ \ \\_.\\\	_\

Bump Pit

Minimum

_ Diameter (D', _

Minimum

Depth (HI

Figure I
Pump	Minimum	Minimum
Model	Diameter (D)	Depth (H)
390.305001	12" (305ram)	24" (610mm)
390.304790	10" (254mm)	20" (508mm)
390.305790