Sears 153.326662 50 GAL. MEDIUM Thermostat Removal/Replacement, Element Cleaning/Replacement

Page 19

The water heater should be drained if being shut down during freezing temperatures. Also, periodic draining and cleaning of sediment from the tank may be necessary.

1.Before beginning turn “OFF” the electric power supply to the water heater.

2.CLOSE the cold water inlet valve to the water heater.

3.OPEN a nearby hot water faucet and leave open to allow for draining.

4.Connect a hose to the drain valve and terminate to an adequate drain or outdoors.

5.OPEN the water heater drain valve to allow for tank draining.

NOTE: If the water heater is going to be shut down and drained for an extended period, the drain valve should be left open with hose connected allowing water to terminate to an adequate drain.

6.Close the drain valve.

7.Follow “Filling the Water Heater” instructions in the “Installation Instructions” section.

8.Turn “ON” power to the water heater.

Never use this water heater unless it is completely full of water. To prevent damage to the tank and heating element, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” power.

Thermostat Removal/Replacement

1.Turn “OFF” the electrical power to the water heater at the junction box.

2.Remove the access panel and the insulation cap with handle.

3.Lift out the tab as shown below to unclip the terminal cover from the thermostat. The terminal cover can now be removed from the thermostat.

FIGURE 29.

4.Disconnect wires from the thermostat.

5.Remove the thermostat from behind the thermostat bracket.

6.Place the new thermostat in the bracket making sure it fits firmly against the tank.

7.Attach the wires to the new thermostat.

NOTE: Some of the terminals may require straight-in wiring through an eye-opening. If wires are now looped, recut and strip wire 3/8” to a straight length and insert.

8.Put plastic terminal cover back in place.

9.Replace the insulation cap with handle to cover the thermostat.

10.Replace access panel, then turn the electric power on.

Element Cleaning/Replacement

NOTE: These instructions are written for element cleaning and element replacement for the lower element. If it is necessary to clean or replace the upper element, then repeat these instructions.

To remove the element from your tank in order to clean or replace it.

19

Image 19
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Power Miser Electric Water HeaterSafe INSTALLATION, USE and Service General Safety Table of Contents Introduction Product SpecificationsBasic Tools Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Materials NeededRemoving the Old Water Heater Installation InstructionsInsulation Blankets Facts to Consider About the LocationFacts to Consider About Convertible Lower Element Water Piping Valve and Pipe Insulation Temperature-Pressure Relief ValveFilling the Water Heater Converting the Lower Element Page Wiring Page Wiring Diagrams Thermostats Service and AdjustmentTemperature Regulation Temperature Settings Upper and Lower Thermostat AdjustmentsAnode Rod Inspection Temperature-Pressure Relief Valve OperationDraining Element Cleaning/Replacement Thermostat Removal/ReplacementPage Page Service Drain Valve Washer ReplacementStart Up Conditions TroubleshootingOperational Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Model Numbers Repair Parts ListBuss Bar Kit 9001591 153.326862 Gallon Short 153.326863 Page Page MY-HOME

153.326663 50 GAL. MEDIUM, 153.326862 50 GAL. SHORT, 153.326362 30 GAL, 153.326563 55 GAL, 153.326762 40 GAL. MEDIUM specifications

Sears has been a prominent name in retail for over a century, renowned for providing various household products to consumers. Among their extensive lineup of items are the versatile water heaters catering to different household needs. The Sears water heater series includes models like the 153.326662 50 GAL MEDIUM, 153.326363 30 GAL, 153.326463 40 GAL, 153.326763 40 GAL MEDIUM, and 153.326562 55 GAL. Each of these models showcases unique characteristics suited for different preferences and household sizes.

The 153.326662 50 GAL MEDIUM is designed to deliver ample hot water for larger households. It features high-efficiency insulation, which minimizes heat loss and boosts the overall energy efficiency of the unit. This model is equipped with a powerful heating element that quickly recharges the water supply, ensuring that you never run out of hot water during peak usage times.

On the other hand, the 153.326363 30 GAL model is a perfect fit for smaller homes or apartments, where space is at a premium. Despite its compact size, it features advanced heating technology that efficiently warms water without significant energy expenditure. This model also includes built-in safety features, such as automatic shut-off valves and a corrosion-resistant tank, enhancing durability and performance.

The 153.326463 40 GAL and the 153.326763 40 GAL MEDIUM units offer an optimal balance for medium-sized households. These models boast similar capacities but differ slightly in their energy consumption profiles. Both models are equipped with smart technology that allows for easy temperature adjustments and energy efficiency monitoring. Additionally, they include user-friendly digital displays that provide instant feedback on water temperature and heating status.

Finally, the 153.326562 55 GAL model stands as one of the larger offerings from Sears. Its substantial capacity ensures that even the most demanding households can rely on a consistent supply of hot water. Like the others, this model incorporates the latest in heating technology, making it efficient and cost-effective over time.

In conclusion, Sears' lineup of water heaters—whether it's a compact 30-gallon unit or a robust 55-gallon solution—caters to a diverse range of consumer needs. Each model combines efficiency, safety, and practicality, making them reliable choices for homeowners seeking effective hot water solutions.