GE CC-SCSTAT installation manual Up and down buttons, Menu button, Mode button, Fan button

Page 9

5

Up and down buttons

The Up and Down buttons adjust the setpoint temperature. Press Up to increase the setpoint value by one degree and press Down to decrease the setpoint one degree. Pressing and holding a button down will cause the setpoint to continuously change until the button is released. The setpoints can be set from 6 to 109° (F or C), unless limited in the installer settings.

You cannot lower the cooling setpoint below the heating setpoint. The thermostat will push the heating setpoint lower if you try to lower the cooling below the heating setpoint. It maintains a setpoint delta separation between heating and cooling setpoints. The same is true for raising the heating setpoint above the cooling setpoint. Again, the thermostat will push the cooling setpoint up to maintain the setpoint delta separation.

Menu button

The Menu button changes the screen display to the Main menu screen that shows other functions available on the thermostat. These are dynamic and can change with the version of the thermostat you have, but the standard ones include:

Messages screen on page 8

Schedule setup screen on page 9

User settings screen on page 12

Thermostat information screen on page 16

Mode button

The Mode button controls the HVAC system mode. The current mode selected is displayed above the button. Pressing the Mode button will cause the mode and display to change to the next mode. The mode cycles through the following modes with each press of the Mode button.

Off mode. The system is off. No heating or cooling will come on. If it was on, the system will turn off. Heat mode. Only heating operation will occur.

Cool mode. Only cooling operation will occur.

Auto mode. Heating or cooling will come on according to the heating and cooling setpoints. The system will automatically switch between heating and cooling when the temperature exceeds the setpoints.

EH mode. This mode is only displayed when Heat Pump HVAC system type is selected. When there is a compressor failure with the heat pump system, setting the mode to EH will allow the supplemental heat to come on whenever there is a heat call to provide heating. It also disables the compressor outputs to prevent further damage to the system.

Fan button

The Fan button controls the HVAC system’s manual fan. The current manual fan mode is displayed above the button. Normally this button is in the Auto mode (the system fan is automatically controlled by the HVAC system). Pressing the Fan button once will turn the manual fan operation on. Pressing it again will turn the manual fan off and return to the Auto mode. Changes in the fan mode are sent to the control unit.

Image 9
Contents SmartCommand Thermostat Installation ManualPage Contents Contacting technical support Safety terms and symbols PrefaceConventions used in this document Product overview Wall display unit WDUWDU control buttons WDU screens WDU LEDsThermostat control screen Temperature displaySetpoint display Clock displayUp and down buttons Mode buttonMenu button Fan buttonLED 2 green, system Economy mode display Communication error displayRun/Hold button LED displayDone. Return to Thermostat control screen on Main menu screenMessages Messages screenSchedule setup screen Schedule setup screenHeat and cool schedule screen Heat and cool schedule screenBack. Return to the Heat and cool schedule screen on Copy schedule screenUser settings screen User settings screenSet clock screen Set clock screenSensor calibration screen Sensor calibration screenBacklight display screen Backlight display screenThermostat information screen Thermostat information screenInstaller settings screen Installer settings screenNetwork settings submenu Page Wiring overview Installation overviewFreeze protection Freeze protectionWiring Wall display unit installationMounting Remote sensor connectionControl unit to WDU wiring Control unit installationControl unit to Hvac wiring Retrofit wiringStandard Hvac system wiring Hvac system wiringHvac system 24 VAC transformer DIP switchesW2/O CO Heat pump Hvac system wiringDIP switches Common or split transformer systems Control unit connectionSerial communication RS485 com portRS485 address RS485 protocol Thermostat network commandsThermostat bench test System checklistSerial communication test Under the Settings tab, go Ascii setupHvac system wiring example Hvac system testingHeat pump system quick test Standard Hvac system quick testHvac system transformer Control unit wiringDIP switch SW1 settings Network commands Serial network command and variable listNetwork variables Name Variable data Default valueOnline publication library Contacting technical supportSmartCommand Thermostat Installation Manual

CC-SCSTAT specifications

The GE CC-SCSTAT is a cutting-edge control system designed for power generation and distribution applications. This advanced platform is engineered to enhance efficiency, reliability, and safety in industrial environments, making it a preferred choice among operators in various sectors, including oil and gas, manufacturing, and utilities.

One of the main features of the GE CC-SCSTAT is its robust data acquisition and control capabilities. It integrates a comprehensive suite of sensors and monitoring tools that allow for real-time tracking of system performance. This functionality is crucial for identifying anomalies and optimizing operational parameters, ultimately leading to reduced downtime and increased productivity.

The system utilizes advanced communication protocols, such as Ethernet and Modbus, facilitating seamless integration with existing infrastructure. This interoperability ensures that organizations can implement the CC-SCSTAT without the need for extensive system overhauls, thus minimizing capital expenditure and disruption to ongoing operations.

In terms of technology, the GE CC-SCSTAT employs state-of-the-art algorithms for predictive maintenance and performance analytics. These capabilities are powered by machine learning and artificial intelligence, enabling the system to learn from historical data and predict potential failures before they occur. This proactive approach to maintenance not only extends the lifespan of equipment but also contributes to significant cost savings over time.

Another noteworthy characteristic of the CC-SCSTAT is its user-friendly interface, which provides operators with easy access to vital system information. The intuitive dashboard displays key performance indicators (KPIs), alarms, and alerts in a clear and organized manner, allowing for quick decision-making and response. Additionally, the system supports mobile access, enabling operators to monitor and control processes from remote locations.

Safety is a fundamental aspect of the GE CC-SCSTAT design. The system incorporates multiple layers of security features, including redundancy and failover mechanisms, ensuring continuous operation even in the event of a component failure. Furthermore, compliance with industry standards and regulations guarantees that the system adheres to best practices in safety and reliability.

In conclusion, the GE CC-SCSTAT stands out as a robust control system with advanced features and technologies. Its integration capabilities, predictive analytics, user-centric design, and unwavering focus on safety position it as a leading solution in the power generation and industrial control sectors. As organizations increasingly look to enhance operational efficiency and sustainability, the CC-SCSTAT proves to be a valuable asset in achieving these objectives.