Bryant TZEMT400AB32MAA manual Attach all wires securely to the new thermostat

Page 6

13 Attach all wires securely to the new thermostat.

Note: A wire must be connected to “24COM” to power the thermostat.

a. Use the information from step 12 to match the wires to the correct terminals. b. Use 1/8” blade screwdriver to secure wires in terminals.

24COM 24RC 24RH W1 W2/0 G

CAUTION: EQUIPMENT DAMAGE HAZARD - Improper wiring can lead to equipment damage.

Follow the Terminal Connection information from step 12 carefully to ensure the control is wired properly. After wires are secure, bare wires MUST NOT touch each other.

14 If necessary, cut the internal jumper wire (JP1).

Skip this step if there is a single wire connected to either “24RC” or “24RH”. However, if there is a wire connected to BOTH “24RC” and “24RH”, see the information below about cutting the JP1 jumper.

If terminals 24RC and 24RH both have wires connected to them,

the JP1 jumper wire must be cut. The jumper is located on back of the thermostat face as shown in the illustration to the right.

IMPORTANT - Before cutting the JP1 jumper, recheck the labels on your wiring against the chart on page 12 to verify that both terminals (24RC and 24RH) were used on the old thermostat and should have wires connected to them on the new thermostat.

24COM

 

24RC

 

24RH

24COM

W1

24RC

W2/0

24RH

G

Y1

W1

W2/0

Y2

G

Y1

Y2

TOJUMPER CUT

 

JP1

2

TOJUMPER CUT

JP1

2

RC/RHSPLIT

 

2

RC/RHSPLIT

2

 

2

2

 

 

 

15 Attach the thermostat face to the wall plate.

a.Tuck wiring fl at inside the wall plate.

b.Carefully place the face plate against wall plate while aligning pins into wire terminals.

c.Push thermostat face into wall plate until it is secure.

If thermostat face does not easily slide into wall plate,

DO NOT force it. Check alignment of pins on back of thermostat face. Also, make sure wiring is pressed fl at and is not bunched together.

24COM 24RC 24RH W1 W2/0 G

Y1 Y2

Wires pressed flat

16 Turn power to heating and cooling system back on.

The thermostat display should turn on and begin displaying information. If the thermostat display does not come on, go back

 

through the installation steps and look for problems. Pay special attention to steps 3 and 12.

6

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Thermostat Guide Physical Installation and Wiring If your existing thermostat is battery poweredWire colors Letters may vary Identify your System Type from the list below Remove existing wall plateMark two mounting holes using new wall plate Install new wall platePrepare two mounting holes Review the wiring chart information Themostat Brand Wire LabelsConnects to Turn power to heating and cooling system back on Attach all wires securely to the new thermostatIf necessary, cut the internal jumper wire JP1 Attach the thermostat face to the wall plateIf your System Type is System Settings at ThermostatSet Time and Date If your Gas or Electric furnace system also has19B Electric Furnace Mechanical Settings 19C Heat Pump Mechanical SettingsPerform System Checkout Test Cooling Operation if your system has coolingTest Heating Operation if your system has heating Enroll the thermostat into the bridge Enroll Thermostat into Schlage LiNKTM SystemPrepare the bridge for enrollment Verify enrollment of the thermostatEstablish Online Control of the Thermostat

TZEMT400AB32MAA specifications

The Bryant TZEMT400AB32MAA is a versatile and advanced thermostat designed to enhance the control and efficiency of heating and cooling systems in modern homes. With its user-friendly interface and a rich set of features, this smart thermostat offers a seamless way to manage indoor climate.

One of the primary features of the TZEMT400AB32MAA is its Wi-Fi connectivity, allowing homeowners to control their heating and cooling systems remotely through a smartphone app. This ensures that you can adjust your home’s temperature from anywhere, providing comfort before you arrive and saving energy when you’re away. The app is compatible with both iOS and Android devices, making it accessible for a wide range of users.

The thermostat also boasts a large, easy-to-read color display that presents information clearly. It shows the current temperature, set point, and operational mode, making it simple to monitor your system at a glance. The intuitive touchscreen interface allows for quick adjustments and programming, eliminating the need for complex navigation.

Another significant feature is its programmable scheduling capabilities. Users can create personalized schedules for different days of the week, optimizing energy savings and comfort based on daily routines. The TZEMT400AB32MAA can store multiple schedules, which can be easily adjusted or overridden as needed.

The smart thermostat also employs advanced energy-saving technologies, including learning algorithms that adapt to your preferences over time. This means the thermostat can automatically adjust settings based on your habits, ensuring optimal energy usage without sacrificing comfort.

Additionally, the Bryant TZEMT400AB32MAA supports multi-stage heating and cooling systems, making it suitable for various HVAC configurations. It is designed with compatibility in mind, working seamlessly with gas, oil, electric, and heat pump systems, including backup heating.

Moreover, it features smart alerts and reminders, notifying users of filter changes or maintenance needs, which can prolong the life of the HVAC system and maintain its efficiency.

In summary, the Bryant TZEMT400AB32MAA represents a significant advancement in home temperature control technology. With its smart features, user-friendly interface, and energy-saving capabilities, it provides homeowners with a reliable solution for managing their indoor climate efficiently and conveniently. Whether you’re looking to save on energy bills or simply enjoy a more comfortable living space, this thermostat offers the perfect blend of innovation and practicality.
Top Page Image Contents