Carrier 53DFS250-SL owner manual Brn H, Programming Notes

						The copy command becomes available
						after the maximum number of occupied
						periods are programmed in a day. This
						example uses 1 as the maximum occupied
			Yes			periods ever programmed in one day.
			Select	Yes	or No to copy	I_ I_
			the previous		day's	IlL!
(		"	program	to	this day.	Tu
	x	.......o				BrnH
						.qllllllllP.
						LU	o,.,

Selecting Yes, then pressing Mode will copy the previous day's program and then will ask the same copy question again. If yes is selected each time, this routine will repeat until Saturday is copied to Sunday. After Saturday is copied to Sunday, the copy command is unavailable.

Select the day for Occupied 1.

J'!_• PI'..!Ut_ Am _t

	Adjust the	start time
(_	for occupied	1.

				3 • LI U Pm
				t>
	Adjust		the stop	time
(_	for	occupied 1.
	On
(_	Select	Occupied		I to run
	on this day (On), or not to
)	run this		day (Off).	ON
	Off

Yes		JILl
		Nt'_
		W
Select	Yes	or No to copy
program	to	this day.
the previous		day's

No

Selecting Yes, then pressing Mode will copy the previous day's program and then will ask the same copy question again. If yes is selected each time, this routine will repeat until Sat-

urday is copied to Sunday. After Saturday is copied to Sunday, the copy command is unavailable.

If no is selected, as in previous steps, flashing prompts for input will appear for start and stop times for Occupied 1. If more than one occupied period was selected in Step 1 on page 3, then cool/heat set points, and start/stop times for additional occupied periods will be prompted.

PROGRAMMING NOTES

•If only 1 Occupied period is selected in step 1 on page 3, Occupied 2 and 3 programming steps are skipped. Further, if only 2 occupied periods are selected, Occupied 3 programming steps are skipped.

•Heat and Cool set points for Occupied 1 are the same for every day of the week. Heat and Cool set points for Occupied 2 and 3 can be adjusted differ- ently for each day of the week, if desired.

•If the start time is set later in the day than the stop time, the program will run from the start time

to midnight and from midnight to the stop time on the same day. For example: 9:00pm start, 8:00am stop, on Monday. In this example the program will run from 12:00am Monday to 8:00am Monday and again from 9:00pm Monday to 12:00pm Monday.

•The Unoccupied settings take effect at all times when: (1) the program is on and (2) the current time is outside a preset occupied period. For this reason start and stop times are not necessary for unoccupied.

•If the same start and stop times are programmed in for an occupied period, then it will run 24 hours.

•If one occupied period starts and stops within another occupied period the lower occupied num- ber has priority. For example: If Occupied 3 is pro- grammed to be "on" 24 hours, and Occupied 2 is programmed to run that day, then Occupied 2 set- tings will take over from Occupied 3 between Occu- pied 2 start and stop times.

•To program Occupied 2 and Occupied 3 modes repeat programming steps for Occupied 1.

Tita' l,.-rJm,j

Steps 1 and 2 were performed on page 2. Advanced Setup begins with Step 3.

S_

Pre,s,heModeb

NOtE

Each step

number

is

located at

MODE

_j

the

top

right

corner

of

the d_slay

While

holding the

Mode

button,

for

easy

reference

PROG RAM

enter

the

Advanced

Setup

screens.

/

press

the

Program

button

to

unocc_p_ed_23 o:Select ono,oresidentialmpHeatOFF.

Adjust

the

deadband

from t (1toto6 6degrees,F)

Adjustthe

m_nlmum

d_f

_/1Bt_ebetween

set po_nts.

heating

cooling and

(0 to

6 F)

_)

elect the cycles pel

d=cyeles

per

hour

hour I_mit.

O

?y ,im.ofoo,od

d 1=d

+ defeat

5 rain.

Compressor

lockout,

{d,

dl,

2-6)

Select

th

ity

level:

0=no

security

in effect

(_

2=1=set programpointrangeon limitedlimesall

3=2 + prohibits

set

point

_

_

changes

Adiust

the

maximum

/_

when secudty is in effect,

(Step 8 only appears if

__

_

Step 7 _snot O)

(35

-

99

F)

P=I

PAII_I

135-

99F)

Ll./

,'.S:,

Adjust

the

minimum

allowable

cool

set point

when security is n effect.

(Step 7gisonlynol

appearsO)

if

Page 4