Emerson 1F97-391 operating instructions

Page 8

INSTALLATION AND CONFIGURATION

ATTENTION!

REMOVE OLD THERMOSTAT ATTACH BASE TO WALL

This product does not contain mercury. However, this product may replace a unit which contains mercury.

Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury. Wearing non- absorbent gloves, take up the spilled mercury with sand or other absorbent material and place into a container which can be sealed. If a cell becomes damaged, the unit should be discarded.

Mercury must not be discarded in household trash. When the unit this product is replacing is to be discarded, place in a suitable container and return to White-Rodgers at 2895 Harrison Street, Batesville, AR 72501 for proper disposal.

Shut off electricity at main fuse or circuit breaker box until installation is complete AND the jumper leads (fig. 10, page 17) on the back of the thermostat are configured properly.

Remove the front cover of the old thermostat. With wires still attached, remove wall plate from the wall.

Identify each wire attached to the thermostat using one of the labels enclosed with the new thermostat.

Disconnect the wires from the old thermostat one at a time. DO NOT let the wires fall back into the wall.

Install the new thermostat using the following procedures.

Remove packing material from the thermostat. Place fingers of one hand on the center top and bottom portion of the thermostat. Grasp the base in the other hand on top and bottom center and gently pull straight out. Forcing or prying on the thermostat will cause damage to the unit.

Place the base over the hole in the wall where the wires come out and mark mounting hole locations base as a template. Drill 3/16” pilot holes, and install screw anchors in the wall.

Run wires through hole in base and attach base to wall (see fig. 2, page 7).

Insert the wires into the terminals on the base using the appropriate wiring diagram and tighten the terminal screws.

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents SeriesTM Easy, Menu-Driven Set-Up Programming Introduction Installation/Configuration Introduction Introduction Specifications Precautions Page Configuring Programming Thermostat baseWiring Diagrams Letter Identification for Wiring Diagrams From heating system Through zone valve Typical wiring diagram for heat/cool, two-transformer system Typical wiring diagram for three-wire cooling system Typical wiring diagram for 24V humidifier system Typical wiring diagram for 120V humidifier system Configuration Jumpers Jumper locations Configuration Menu Configuration Menu cont’d Configuration Adjustable Anticipation Cool FAN-ON FAN-OFF DelayConfiguration Optional Remote Temperature SenseCompressor Lockout Disabling HEAT, COOL, or Auto ModesCheck Thermostat Operation FAN OperationHeating System Until FAN Auto isResetting Thermostat Cooling SystemManual Operation Bypassing the Program Programmed Operation Planning Your ProgramCool, or Auto Entering Your Program To Set the ClockProgramming Day Sample Heat Program Schedule Shows factory programming Day Sample Cool Program Schedule Shows factory programming Day Personal Heat Program Schedule Day Personal Cool Program Schedule Features Pushbutton Backlight Factory PreprogrammingArm Chair Programming Temporary Program OverrideAdjustable Temperature Display Automatic Heat/Cool ChangeoverProgrammable Vacation Time/ Temperature Operation Battery Back-UpProgrammable Fan Control Daylight Savings Time ButtonThermostat Startup After Total Power Loss Keypad LockoutCompressor Short-Cycle Protection Air Filter Change-Out IndicatorSystem Thermostat Diagnostics Adjustable Humidity Display Humidifier Maintenance IndicatorHumidifier Control Monitoring Programmable Automatic Humidity ReductionFAQs 1F97-391 Word Check BatteryFAQs FAQs 1F97-391 FAQs 1F97-391 Troubleshooting Does not click, try the reset operation by pressing Temperature Display Adjustment in the Configuration To the Configuration section page 19, step Index Index Page Page Part no -6459A

1F97-391 specifications

The Emerson 1F97-391 is a sophisticated, programmable thermostat designed to enhance comfort and efficiency in residential heating and cooling systems. With its sleek design and user-friendly interface, this thermostat stands out for those looking to upgrade their home climate control.

One of the main features of the Emerson 1F97-391 is its ability to be programmed for up to seven days. This allows users to set different temperature schedules for different days of the week, which is particularly useful for families with varying routines. The thermostat also boasts a large, backlit display that makes it easy to read temperature settings and other information, even in low-light conditions.

In terms of technology, the Emerson 1F97-391 is equipped with Smart Response technology, which learns your heating and cooling patterns and adjusts accordingly. This feature is designed to ensure that your home reaches the desired temperature by the time you're scheduled to arrive, optimizing energy efficiency. Additionally, the thermostat can be paired with Wi-Fi connectivity, allowing for remote access through a mobile app. This means users can adjust their home’s temperature from anywhere, ensuring comfort upon arrival.

Another significant characteristic of the Emerson 1F97-391 is its compatibility with a wide range of HVAC systems, including single-stage and multi-stage systems, heat pumps, and gas or electric furnaces. This versatility makes it an ideal choice for a variety of homes and setups.

Moreover, the thermostat features a built-in humidity sensor, providing users with not only temperature control but also the ability to monitor and manage indoor air quality. This is crucial for maintaining a comfortable living environment and can contribute to overall health and well-being.

The Emerson 1F97-391 also incorporates energy-saving functions such as Eco mode and built-in reminders for filter changes. These features help users maintain their systems efficiently while ensuring optimal performance over time.

In summary, the Emerson 1F97-391 is a modern thermostat offering programmable capabilities, advanced technology like Smart Response, and compatibility with various HVAC systems. It encompasses features focused on energy efficiency and user convenience, making it an excellent choice for anyone seeking to enhance their home’s climate control system.
Top Page Image Contents