Cadet SBFT2 installation instructions Baseboard/Thermostat Wiring, Completion of Installation

Baseboard/Thermostat Wiring

Thermostat in left junction box: (Figure A)

1.Locate and cut closed end splice of wires containing limit lead wire and return wire (wire behind deflector). Strip 1/2" of insulation from these two cut lead wires.

a.Join the lead wire from the limit with the lead wire from thermostat terminal J5L2 with a connector.

b.Join the return wire (wire behind deflector) with the lead wire from thermostat terminal J1T1 with a connector.

2.Connect the grounding lead of the power supply to the supplied grounding pigtail (copper wire attached to case in junction box) with a connector.

3.Connect each of the remaining two power supply leads to each lead from the thermostat rocker switch with a wire connector.

a.Be sure the panel does not interfere with the mounting of the thermostat plate. Move panel if needed. (Using a rubber- coated tool, or hammer handle; carefully pry upwards.)

4.Carefully push wiring back into junction box, hook upper edge of face- plate under lip of case. Lower bottom edge of faceplate to junction box surface and secure thermostat with mounting screw.

5.Rocker switch should be placed in the “0” (OFF) position. To finish see the “Completion of Installation” section below.

Thermostat in right junction box: (Figure B)

1.Cut closed end splice from connection of element lead wire and return wire (wire behind deflector). Strip 1/2" of insulation from these two cut lead wires.

a.Join the lead wire from the element with the lead wire from thermostat terminal J5L2 with a connector.

b.Join the return wire (wire behind deflector) with the lead wire from thermostat terminal J1T1 with a connector.

2.Connect the grounding lead of the power supply to the supplied grounding pigtail (copper wire attached to case in junction box) with a connector.

3.Connect each of the remaining two power supply leads to each lead from the thermostat rocker switch with a wire connector.

a.Be sure the panel does not interfere with the mounting of the thermostat plate. Move panel if needed. (Using a rub- ber-coated tool, or hammer handle; carefully pry upwards.)

4.Carefully push wiring back into junction box, hook upper edge of faceplate under lip of case. Lower bottom edge of faceplate to junc- tion box surface and secure thermostat with mounting screw.

5.Rocker switch should be placed in the “0” (OFF) position. To finish see the “Completion of Installation” section below.

FIGURE “A” (Left Junction Box Wiring)

Completion of Installation
At this point, the baseboard should be securely mounted, and the SBFT2
	FIGURE “B” (Right Junction Box Wiring)
thermostat wired and secured to the baseboard junction box. The other
junction box should have the baseboard end plate/cover secured in place.
Verify that the thermostat rocker switch is in the “O” (OFF) position before
reestablishing the electrical power at the panel for power flow to the base-
board heater.
Refer to the programming guide for the operation of the SBFT2 thermostat.

Warranty

LIMITED ONE-YEAR WARRANTY: Cadet Manufacturing Co. will repair or replace any Cadet product, including thermostats, found to be defective or malfunction- ing from first date of purchase through the first year.

These warranties do not apply:

1.To conditions resulting from improper installation or incorrect supply voltage;

2.To conditions resulting from improper maintenance, misuse, abuse, accident, or alteration;

3.To service calls, or any warranty labor not performed at the Cadet Manufacturing facility;

4.If the date of manufacture cannot be determined;

5.To freight damaged products.

CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH AS PROPERTY DAMAGE AND/OR INCIDENTAL EXPENSES RESULTING FROM BREACH OF THESE WRIT- TEN WARRANTIES OR ANY IMPLIED WARRANTY.

These warranties give you specific legal rights, and you may also have other rights which vary from state to state. Cadet neither assumes, nor authorizes anyone to assume for it, any other obligation or liability in connection with these electric heaters or any part of such heaters.

If the product should become defective during the warranty period, contact Cadet Manufacturing Co. at 360-693-2505 for instructions on how to have the repair or replacement processed. Products returned without authorization will be refused.

Parts and Service

Contact Cadet for information on Parts or Service.