Niles Audio HDCTR, HDLRS manual Installation Brackets, Frames Grilles Existing Walls

Page 9

Installation of Brackets, Frames and Grilles in New Construction

The grille is constructed of aluminum with a perfectly even powder coat overall. This powder coat is an ideal primer.

Remove the grilles before painting. If you are using spray paint, use two thin coats without any primer. If you are using a compressor and a spray gun, use the finest, most diffuse setting. Practice first on some paper if you have no experience painting with spray paint.

If you are using an applicator or brush, and a can of paint, thin the paint first. You do not want to have to poke hundreds of holes in your beautifully painted grilles.

Figure 14

Figure 15

Installation of

Brackets, Frames

and Grilles in

Existing Walls

IMPORTANT: Before you cut into any wall, review the sections on running wire and speaker placement.

1.Drill a 1/8” pilot hole just barely through the wallboard or dry wall (1/2” to 5/8” deep in most homes) about an inch below the center of your proposed speak- er location (an inch to the side if you are mounting the speaker horizontally). BE VERY CAREFUL NOT TO DRILL THROUGH EXISTING WIRES, PIPES, OR STRUCTURE. IF YOU FEEL ANY EXTRA RESISTANCE AS YOU ARE DRILLING, STOP. Cut a piece of coat hanger equal to the width of the bracket. Bend the wire in half creating a right angle. Poke the “L- shaped” wire into the pilot hole and turn it

Figure 17

Figure 16

in a complete circle. If it turns freely, repeat the procedure from a hole about an inch above the center of your proposed speaker location (See Figure 16).

If the wires movement is obstructed by a pipe or cable, fill the hole(s) with spackle or other patching compound and try another location.

2.When determining the final location of the cutout keep in mind that the frame and bracket will extend beyond the cutout. Make sure that you do not place the edge of the cutout directly next to a stud. Locate the studs using a stud sensor or hand-knocking. Once you have deter- mined the correct position for the cutout, hold the supplied template up to the wall surface. Level the template in either the horizontal or the vertical position and

mark the wall with a pencil.

Drill the four corners with a 1/4” drill bit.

3. If you are cutting a painted or wall papered drywall use a sheetrock or keyhole saw. Cut the hole with the saw at a 45 degree angle. That way,

Installation of Brackets, Frames and Grilles in Existing Walls

15

16

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Hdctrr Hdlrss Introduction Features and BenefitsInstallation Considerations Installation ConsiderationsIncorporating a Remote Control Speaker PlacementPlacement of the Front Left and Right Speakers Hdlrs Insulating the Wall CavityPlacement of the Center Channel Speaker Hdctr Placement of the Rear Channel Speakers HdlrsBoundary Effect Running the Speaker Wire in New Construction Installation FundamentalsLocation Concealing Speaker Wire Existing WallsConstruction InstallationStage One Before Drywall is Hung Stage Two Before PaintInstallation Brackets, Frames Grilles Existing Walls Main/Surround Configuration Installing the SpeakerSpeaker Orientation for Directed Sound Field Geometry Defeating DsfgListening at Higher Volumes Speaker PhaseCleaning OperationLimited Warranty SpecificationsWarranty Limited

HDCTR, HDLRS specifications

Niles Audio has a longstanding reputation in the realm of home audio solutions, and its HDCTR and HDLRS models are exemplary representations of the brand's commitment to high-performance audio technology. These models cater to enthusiasts looking for comprehensive audio experiences with cutting-edge features and advanced engineering.

The Niles HDCTR, a center channel speaker, is designed to provide clarity and depth for dialogue and soundtracks in home theater setups. One of its main features is the use of advanced, high-efficiency drivers that reproduce a wide frequency range, ensuring that every nuance in sound is captured. The speaker is engineered with a high-performance 6.5-inch woofer coupled with dual 1-inch soft dome tweeters, allowing it to deliver an impressive audio performance whether you’re watching movies or listening to music.

On the other hand, the HDLRS model stands out as a pair of surround speakers that enhance the immersive experience whether in a stereo or surround sound configuration. Each speaker utilizes a 6.5-inch woofer and dual 1-inch tweeters for a balanced sound stage. The design of the HDLRS also allows for flexible placement options, making it easy to integrate into diverse home environments.

Both models feature Niles' proprietary technologies that minimize distortion and improve dynamic range, enhancing overall listening pleasure. The HDCTR is equipped for wall-mounting, allowing for seamless integration into your home theater system. Meanwhile, the HDLRS includes adjustable mounting brackets which enable precise angling to optimize sound directionality.

In terms of build quality, both speakers boast a robust design with attractive aesthetics that can complement any room decor. The cabinets are crafted from durable materials that not only withstand the test of time but also help to reduce unwanted resonance, thereby improving audio fidelity.

Furthermore, the low impedance design of the HDCTR and HDLRS models ensures compatibility with a wide range of AV receivers, making them accessible for both professional installers and casual users alike. This level of flexibility makes them excellent choices for those looking to elevate their audio experience, whether for casual listening or serious home theater setups.

Overall, Niles Audio's HDCTR and HDLRS speakers embody a perfect blend of style, performance, and technological innovation, catering to audiophiles who seek unmatched sound quality and versatile solutions for their audio needs.
Top Page Image Contents