Assa Model 34, 32 manual Magnalock Mounting

Page 10

Rev. A.5, 8/03

Page- 7

FIG. 7: F MAGNALOCK MOUNTING

Roll pin plastic bushing require 1/2" (12.7mm) holes and must be shortened to work in Z bracket. Roll pin bushings may be omitted if lock is

not Senstat. Then drill 3/ Header 8" (9.5mm) holes for roll

pins.

Sex Bolt

Drill 1/2" (12.7mm) hole

 

 

Architectural Cover slides on

 

 

last with open side up and is

 

 

attached with supplied double

 

Strike

stick tape

Magnet

Z Bracket

 

 

 

 

 

 

T-Nut requires 3/8" (9.5mm) Dia

 

 

 

 

hole in bracket and accepts

 

 

strike mounting screw

 

 

Use 1" mounting screw supplied

 

 

with Z bracket, PN# 300-13400

 

 

or 300-13450 (metric)

 

 

Washer Stack

 

Z Bracket

 

Cap Screw:

5/16" x 18, PN# 300-13500 or 8mm-1.25mm, PN# 300-13425 (metric)

#14 Hex Sheet Metal Screw (2) PN# 300-13200

Door

2.5MOUNTING PROCEDURES FOR SPECIFIC DOOR TYPES 2.5.1 ALUMINUM FRAME GLASS DOOR MOUNTING

This is a common door type that utilizes the Magnalock. Certain mounting problems can arise depending on the configuration of the door and frame. Often, the header is not wide enough for the depth of the magnet. This can mean that none of the mounting screws can be run into the header or that in the case of the model 62 and 82, only two of the four will fit. Another aspect of the mounting screw problem is that the screws might line up with the end of the header extrusion. Also the wires may exit beyond the end of the header so that they will be exposed and vulnerable to tampering.

Most of the problems are solved by the use of Securitron's Universal Header Bracket (part # UHB-CL or UHB-BK). This bracket will function with the model 32, model 34 or model 62 Magnalock. A separate version (UHB-82) is offered for use with the longer model 82. The UHB extends the depth of the header either 1" (25mm) or 1 1/2" (38mm) depending on which way it's oriented. This usually allows mounting of all screws and since the bracket is itself a hollow extrusion, the wire is run inside the bracket and therefore is hidden. Even with use of the bracket, it is possible that one set of mounting screws may line up with the end of the header when the model 62 or 82 is used. To deal with this situation, some adjustment of the magnet mounting position is possible. Instead of the two rubber washers supplied with the strike, one or three may be used. If the door is secured only by the Magnalock (there is no mechanical swingbolt) the door closed position may be altered to allow all mounting screws to be used. Finally note that a model 62 installation on this type of door is acceptable if only two mounting screws are used. Since the screws run into steel nuts, the fastening technique is very strong. It is best to use all four screws, but particularly on this type of door, which is inherently not high security (the glass may be shattered for forced entry) firmly mounting two screws is acceptable.

Aluminum frame headers typically employ a “blade” stop which is far too thin to provide a mounting surface for the magnet. Note that Figure 5 shows the Magnet mounting on the door stop. Accordingly, on aluminum frame glass doors, the magnet body mounts directly onto the header. This can be accomplished by cutting away a section of the blade stop. This technique is preferred in that the projection of the magnet into the opening is minimized. An alternate

Image 10
Contents General Installation on Inswinging Door General Installation on Outswinging DoorMounting Procedures for Specific Door Types Avoiding Poor Release Characteristics Appendix C Considerations for Maximum Physical SecurityRev. A.5, 8/03 Survey Physical InstallationInstallation Tool KIT Strike Plate MountingSteps in Mounting the Strike Standard Magnet Dimensions and Assembly Mounting the MagnetStrike Dimensions and Assembly General Installation on Inswinging Door with Z Bracket Collapsing the Blind NutsMagnet Dimensions Magnalock Mounting UMB-BRACKET for Aluminum and Concrete Filled Headers Solid Glass Door MountingUSE of the UMB Bracket with the Model 34 Magnalock Double Door Mounting Steel Header Filled with Concrete or Wood Frame MountingWood Frame and Concrete Header Bracket Mounting Techniques for Gates USE of Dress Covers Tamper Proofing the Magnalock Electrical InstallationGeneral Electrical Characteristics Standard LockWiring Considerations to Avoid Slow Release Wire Gauge SizingDouble Door Procedure for Status Reporting Senstat Magnalocks SCDouble Door Control Switching Emergency ReleaseMagnacare Limited Lifetime Warranty PatentsAppendix a Troubleshooting PROBLEM-- Reduced holding forceWire Gauge Resistance/1,000 ft Appendix C Considerations for Maximum Physical Security