Assa ELECTRIC LOCK manual Rev. A.1, 10/99

Page 22

Rev. A.1, 10/99

Page- 20

Most installations do not require use of the bypass function. Even if there is a local authorized entry or exit device at the door, it will often have its own timed relay output. We believe that the LCP/XDT combination works more clearly when the bypass function is not used and therefore recommend employing the first connection scheme shown in Figure 9 where possible.

Figure 9 shows the general case of an LCP/delayed exit installation. Delayed exit takes place at the door as controlled by the initiate and reset switches. The LCP panel serves two functions. It releases the lock for authorized entry or exit and also monitors the door as follows:

In the normal (secure) condition, the main LED is green and no alarm sounds.

During the nuisance delay and release delay period, the main LED remains green but the "AM" LED illuminates yellow and a pulsing Sonalert sounds.

When the lock releases at the end of the delay, the yellow AM LED goes out. The main LED turns red and the steady Sonalert sounds.

When the lock has been reset (relocked), the main LED turns orange and the panel reset toggle may be used to halt the Sonalert and restore the main LED to green.

When the lock is released for authorized use from the panel toggle or from a local release switch, the main LED turns off and the toggle bat illuminates yellow. No alarm sounds.

Note on the drawing that the local release switch may or may not be present. If no local release switch is used, LCP terminal "L" connects directly to XDT terminal "C3" and and to the “top” of the initiate switch (the switch contact that does not connect to “IN”). LCP terminal "E" connects directly to XDT terminal "FE". If there is more than one local release switch, for authorized exit and entry for instance, the NC contacts of the two release switches would connect in series. The NO contacts would each connect to XDT terminal "FE".

There are a number of reasons for the particular wiring method in Figure 9. Note first the connection to terminal “FE” on the XDT board. Inputting +V to this terminal places the XDT board in “free egress” mode which means that the lock will release (relay #3 deenergizes), immediately whenever +V is removed from “IN”. No delayed exit event will begin and the XDT board’s alarm outputs are suppressed. This is the desired effect when either the panel toggle or a local release switch has “legally” released the lock.

Note also that the initiate switch is powered not directly from the power supply but rather through the local release switch. The rationale here is that “IN” should not be powered if either the local release switch or the panel toggle has released the lock. This permits use of the XDT board’s “DC” terminal which can keep the lock secure after the delay has expired subject to use of the initiate device for immediate egress. When this function is employed, it is necessary that the local release switch or panel toggle can still unlock the door whether or not the initiate device is used.

A variation to Figure 9 occurs if you are not employing an LCP panel without the “AM” option. This presents the problem of how to annunciate the release delay period. To accomplish this, remove the jumper from terminal “LS” to +V. Then connect “LS” to the output of the door/lock status switch (no longer connect it to the LCP “S” terminal”). Jump “C1” to “C2” and then connect NO2 to the “S” terminal. With this set-up, the remote alarm relay contact, NO2, will maintain the green LED on the panel in the secure condition. During a delayed exit event, relay #2 will deenergize at the end of the nuisance delay period and this will create an immediate violation alarm at the panel. The same alarm will occur after a five second delay if the door/lock status sensor reports insecure at any time it should be secure, it its output is connected to “LS”.

While Figure 9 shows the general approach to wiring the AM version of the LCP into a delayed exit installation, Figure 10 shows a specific common example where all Securitron products are

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Panel Power Additional Monitoring Lights Option AMSwitch Bypass Wiring Option KP2 or MK2 Powered Switching Devices AT the DoorsSwitch Bypass Wiring Option KP1 or MK1 MASTER/SLAVE Panels for Fail Safe LocksPanel Power GeneralLock Control MonitoringAudible Alarm and Alarm Reset Summary of INDICATOR/SONALERT StatesSilence Latch Option SL OptionsEmergency Release Option PB Momentary Switches Option MOM Switch Bypass Keyswitch Options KP1, KP2, MK1, MK2High Volume Push Buttons Option HT Board Terminal Descriptions Panel Board OverviewWiring Power Input WiringPower Supply to LCP Board Wiring Type 1 Fail Safe Fail Safe LocksType 2 Fail Safe Fail Safe Lock Connections Type 5 Fail Safe Magnalock Type 3 Fail SafeType 4 Fail Safe Fail Secure LocksFail Secure Lock Connections Type 2 Fail Secure Type 1 Fail SecureType 3 Fail Secure Powered Switching Device AT Door Wiring DK-26 + Magnalock Type 4 Fail SecureWiring Unused Zones Wiring with Release Hold Timer Fail Safe and Fail SecureFail SAFE/FAIL Secure Timer Connections Remote Indicator WiringSilence Latch Wiring Option SL Option WiringAC Lock Control Emergency Release Wiring Option PB Field Installation of Emergency Release ButtonGeneral LCP/XDT Connections Without USE of Bypass Rev. A.1, 10/99 LED WHT MK KEY RED Switch General LCP/XDT Connections with USE of Bypass Switch Bypass Wiring Option KP1 or MK1 Fail Safe Locks Field Installation of Bypass Keyswitch Fail Safe Locks Switch Bypass Wiring Options KP2 or MK2 Fail Secure LocksField Installation of Bypass Keyswitch Fail Secure Locks USE of Multiple PanelsConnections Between Standard Board and Slave Board Multiple Panel Fail Secure Wiring Panels Alternately EnabledAlternately Enabled Panel Wiring Door Monitoring no Electric Locks Door Monitoring no Electric LocksMAGNACARE→ Limited Lifetime Warranty

ELECTRIC LOCK specifications

Assa Electric Lock is a cutting-edge security solution designed to address the evolving needs of modern access control systems. Utilizing advanced technologies, this lock integrates both traditional locking mechanisms with state-of-the-art electronic features, providing an unparalleled level of security for residential and commercial properties.

One of the standout features of the Assa Electric Lock is its ability to incorporate various access modes. Users can choose between key-based entry, key fob access, and mobile app control. This versatility ensures that users can select the most convenient method for their specific needs while still maintaining robust security. The inclusion of a mobile application elevates user control, allowing for remote access management and real-time monitoring of lock status.

The lock is engineered with robust materials, ensuring durability and resistance to tampering. It features a high-quality housing that can withstand environmental elements, making it suitable for both indoor and outdoor installations. The Assa Electric Lock is also designed to function seamlessly with existing security systems, providing compatibility without compromising overall security.

Assa Electric Lock employs advanced encryption technologies to safeguard user data and access control commands. With encryption protocols in place, users can be confident that their security information is protected from unauthorized access. The lock also includes an audit trail feature, which logs entry and exit events, allowing property owners to track access history easily.

In addition to its electronic capabilities, Assa Electric Lock prioritizes user-friendly design. The intuitive interface and installation process make it accessible to both professional installers and DIY enthusiasts. Furthermore, the lock is equipped with a backup key option, ensuring that users can always access their property in the event of a power failure or technical issues.

The lock's energy efficiency is another key characteristic, as it operates on low power consumption without sacrificing performance. This commitment to sustainability not only reduces costs but also minimizes the environmental impact.

Overall, the Assa Electric Lock stands out in the evolving landscape of security technology. It combines traditional reliability with modern electronic features, making it an ideal choice for those seeking enhanced security solutions. With its range of access options, robust materials, advanced encryption, and user-friendly design, the Assa Electric Lock is leading the way in secure access control.
Top Page Image Contents