LG Electronics LP091CEM-Y8 manual Architecture Grille Aluminum Single Pack, Architectural Grille

Page 28

Architecture Grille Aluminum - Single

Note:

Pack

A baffle kit must not be used with a stamped aluminum grille

Part No: AYAGALA01

on any PTAC installation.

 

Stamped Aluminum Grille

Stamped Aluminum Grille

Architecture Grille

Description

Outdoor grilles are attached to the wall sleeve and exposed to the exterior wall. The grilles are an industry standard size of 42" x 16".

Receiving

Upon receipt of the product, inspect the shipping carton for signs of visible damage. Report any damage or shortage to the carrier and note it on the delivery receipt. The unit must be stored in its original shipping carton in a dry, secure place prior to its installation and use.

Installation

The installation and servicing of the equipment referred to in this booklet should be performed by qualified, experienced technicians.

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/tagout procedures to ensure the power can not be inadvertently energized. Failure to disconnect power before servicing could result in death or serious injury.

Important Note:

The unit OFF switch does not disconnect all electrical power to this unit.

1.Prepare the wall sleeve for installation of the grille by removing the cardboard stiffener and rear enclosure panel from the sleeve. These items may be removed from inside of the building.

Note:

The sleeve stiffener must be taken out before the rear sleeve enclosure panel can be removed from the sleeve.

2. Prepare the stamped aluminum grille for installation on the sleeve by inserting the six (6) plastic grommets into the square holes located near the outer edges of all four sides of the grille. With the grille positioned so the flanges of all four sides are in the up position, insert the grommets so the square end protrudes through the grille in the opposite direction from the flanges.

3.Turn the grille so it can be removed through the rear sleeve opening.

4.Install the stamped aluminum grille by aligning the guide pins located in the lower right and left hand corners of the grille with the corresponding holes in the rear of the wall sleeve.

5.Secure the grille by threading each of the screws into the plastic grommets.

6.Remove the wire handle (not shown in the picture) from the center of the grille prior to installing the chassis into the sleeve.

Note:

Be sure to keep a firm grip on wire handle and grille to prevent it from dropping and/or causing possible injury or property damage.

Architectural Grille

1.Remove the cardboard sleeve stiffener and the rear enclosure of the sleeve as described in Step 1 of the stamped aluminum grille instructions.

2.Turn the grille so it can be removed through the rear sleeve opening.

3.Install the grille by aligning the four screws supplied to their corresonding holes in the architectural grille.

Copyright ©2008 LG Electronics. Inc. All right reserved.

- 28 -

Only for training and service purposes

LGE Internal Use Only

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents SVC Manual Specification Model LP091CEM-Y8Features and Benefits Sleeve and the Rear GrilleDoor Switch/Occupancy Sensor Outdoor Air Temperature SwitchoverTemperature limits Quick Heater RecoveryControl Locations Operation Electric Heating ModelVentilation Cooling only ModelTemperature Limiting Additional ControlsRemoving the Front Grille Additional ControlsREMOTE/LOCAL Control Energy SaverFront Desk Control Remote Wall ThermostatMechanical Parts Disassembly InstructionsFront Grille Control BOX AIR Handling Parts Electric Heater Electric Heater Model onlyCross Flow FAN Axial FANElectrical Parts ShroudOutdoor Motor CompressorPower Cord 6 P.C.BRefrigeration Cycle CondenserEvaporator Capillary TubeLGE Internal Use Only Pulling Vacuum Installation HOW to Install the UnitDimension of air conditioner Dimension of sleeve assembly optionalWall Case Installation Data Wall Sleeve InstallationGeneral Preparation of the Front Grille Installation of Wall Case in Wall OpeningPreparation of the Wall Case for All Types of Construction LGE Internal Use Only Sub-Base Connected Unit Installation Electrical Safety Electrical RequirementsElectrical Data for 230/208V Model 208, 230, and 208/230 Volt UnitsField Installed Accessories InstallationControl Panel Key Lock DescriptionCondensate Disposal Pump Kit Installation Hazardous VoltagePlace the top cover assembly back into the unit Spraying Architecture Grille Aluminum Single Pack Architectural GrilleDrain Installation Condensate Drain kitOutdoor Drain Kit Installation Outdoor Drain Kit InstallationChecklist Indoor Drain Kit InstallationLeveling Legs Leveling Leg Assembly Leveling Leg Assembly Installation on Wall SleeveJunction Box Kit Installation and Wiring Procedure Hard Wire KitUse Copper Conductors Only 208/230 Volt Units Volt UnitsRemote Escutcheon Kit Standard EscutcheonSubbase Dimensions Outside Dimensions Troubleshooting GuidePiping System Troubleshooting Guide Fails to Start Complaint Cause Remedy Room AIR Conditioner Voltage Limits 208/230V 187V 253VComplaint Cause Remedy Piping Diagrams CN-IDPTSchematic Diagram Part A, there are 3 typesExploded View 435300Condenser Outdoor Service Replacement Procedure Enlarged pictureJanuary

LP091CEM-Y8 specifications

The LG Electronics LP091CEM-Y8 is a standout portable air conditioning unit designed to deliver comfort and convenience in various settings. This model combines efficiency with advanced technology to provide optimal cooling performance, making it an ideal choice for homeowners and renters alike.

One of the main features of the LP091CEM-Y8 is its cooling capacity, rated at 9,000 BTU. This level of power enables it to effectively cool spaces up to approximately 350 square feet, making it suitable for living rooms, bedrooms, or small offices. The unit also boasts a dehumidifying function, which removes up to 2.3 pints of moisture from the air per hour, ensuring a comfortable environment while reducing the risk of mold and mildew.

The LP091CEM-Y8 incorporates a user-friendly interface that includes an easy-to-read LED display. Users can adjust the temperature and settings using the included remote control, providing added convenience. The unit also features multiple fan speeds, allowing users to customize airflow according to their personal preferences.

A standout technological aspect of this model is its Energy Efficiency Ratio (EER), which provides a measure of its cooling efficiency. The LP091CEM-Y8 is designed to operate efficiently, reducing energy consumption while still delivering powerful cooling performance. This energy-saving feature not only helps lower utility bills but also makes the unit an environmentally friendly option.

Additionally, the LP091CEM-Y8 is equipped with a programmable timer, enabling users to set specific operating times. This feature allows the air conditioner to automatically turn on or off based on the user’s schedule, providing a seamless cooling experience. The unit also includes a washable and reusable air filter, which helps to improve indoor air quality by capturing dust and allergens.

Moreover, its compact and portable design includes caster wheels, making it easy to move the unit from room to room. The sleek and modern aesthetic ensures that it fits well with a variety of interior decors.

In summary, the LG Electronics LP091CEM-Y8 is a powerful, efficient, and user-friendly portable air conditioning unit that provides excellent cooling and convenience. Its advanced features, including a high BTU rating, energy efficiency, and easy mobility, make it an outstanding choice for anyone looking to enhance their indoor comfort.
Top Page Image Contents