LG Electronics LP091CEM-Y8 manual Wall Sleeve Installation, Wall Case Installation Data, General

Page 18

3.2 WALL SLEEVE INSTALLATION

3.2.1 Wall Case Installation Data

For new construction, early planning with the architect is necessary. Unit location, electrical connection locations, and wall openings of the proper dimensions are essential to avoid the necessity of rework, fillers, framing, moving electrical outlets, and other expensive modifications.

General

Generally, units are installed 3" to 5" above the floor (flush to finished floor installation is possible) as near to the center of the room as possible; underneath a window or a glass panel is typical. Normal installation of the wall case allows installation flexibility; from flush with the finished interior wall to a minimum of 1/4" of the wall case extending beyond the finished exterior of the building.

Special consideration must be given to installations where the wall case does not extend a minimum of 1/4" beyond the finished exterior wall.

Regardless of the installation, there are several things to consider when selecting a location for installing the unit. For instance, drapery location could interfere with air discharge, and placement of furniture may have an impact on the performance of the unit. The following information is intended to minimize installation problems and assure you of trouble-free installation.

Refer to page 17 for required wall opening dimensions. Minimum recommended interior and exterior case projection for standard wall thicknesses are shown in the drawings in this manual. The case may be installed flush with the finished indoor wall.

Mounting an outdoor grille or louver section to the building face may cause a space between the outdoor coil and the louver section. Air splitters, aligned with the ends of the outdoor coil, must be installed between the outdoor coil inlet and outlet air streams. Gaps between the outdoor coil and the louver section may allow condenser air recirculation and affect the operation of the unit.

The wall case should be level from side to side and from level to 1/4 bubble tilt to the outdoors. The condensate disposal system in the unit is designed to dissipate the condensate water generated during cooling operation in accordance with ARI standards and actually uses this water for maximum unit efficiency. A level unit will also insure proper performance of the Internal Condensate Removal (ICR) system optional on heat pump units.

For existing construction it is important that carpentry, masonry and electrical work be performed by competent, qualified personnel. Since installations in existing construction may involve removal of building material from the structure, locating the wall case must be done correctly.

Copyright ©2008 LG Electronics. Inc. All right reserved.

- 18 -

Only for training and service purposes

LGE Internal Use Only

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents SVC Manual Specification Model LP091CEM-Y8Features and Benefits Sleeve and the Rear GrilleTemperature limits Door Switch/Occupancy SensorOutdoor Air Temperature Switchover Quick Heater RecoveryVentilation Control LocationsOperation Electric Heating Model Cooling only ModelRemoving the Front Grille Temperature LimitingAdditional Controls Additional ControlsFront Desk Control REMOTE/LOCAL ControlEnergy Saver Remote Wall ThermostatDisassembly Instructions Mechanical PartsFront Grille Control BOX AIR Handling Parts Electric Heater Electric Heater Model onlyCross Flow FAN Axial FANOutdoor Motor Electrical PartsShroud CompressorPower Cord 6 P.C.BEvaporator Refrigeration CycleCondenser Capillary TubeLGE Internal Use Only Pulling Vacuum Dimension of air conditioner InstallationHOW to Install the Unit Dimension of sleeve assembly optionalWall Sleeve Installation Wall Case Installation DataGeneral Installation of Wall Case in Wall Opening Preparation of the Front GrillePreparation of the Wall Case for All Types of Construction LGE Internal Use Only Sub-Base Connected Unit Installation Electrical Data for 230/208V Model Electrical SafetyElectrical Requirements 208, 230, and 208/230 Volt UnitsControl Panel Key Lock Field Installed AccessoriesInstallation DescriptionCondensate Disposal Pump Kit Installation Hazardous VoltagePlace the top cover assembly back into the unit Spraying Architecture Grille Aluminum Single Pack Architectural GrilleDrain Installation Condensate Drain kitOutdoor Drain Kit Installation Outdoor Drain Kit InstallationIndoor Drain Kit Installation ChecklistLeveling Legs Leveling Leg Assembly Leveling Leg Assembly Installation on Wall SleeveHard Wire Kit Junction Box Kit Installation and Wiring ProcedureUse Copper Conductors Only 208/230 Volt Units Volt UnitsRemote Escutcheon Kit Standard EscutcheonSubbase Dimensions Troubleshooting Guide Outside DimensionsPiping System Troubleshooting Guide Fails to Start Complaint Cause Remedy Room AIR Conditioner Voltage Limits 208/230V 187V 253VComplaint Cause Remedy Piping Diagrams CN-IDPTSchematic Diagram Part A, there are 3 typesExploded View 435300Condenser Outdoor Service Replacement Procedure Enlarged pictureJanuary

LP091CEM-Y8 specifications

The LG Electronics LP091CEM-Y8 is a standout portable air conditioning unit designed to deliver comfort and convenience in various settings. This model combines efficiency with advanced technology to provide optimal cooling performance, making it an ideal choice for homeowners and renters alike.

One of the main features of the LP091CEM-Y8 is its cooling capacity, rated at 9,000 BTU. This level of power enables it to effectively cool spaces up to approximately 350 square feet, making it suitable for living rooms, bedrooms, or small offices. The unit also boasts a dehumidifying function, which removes up to 2.3 pints of moisture from the air per hour, ensuring a comfortable environment while reducing the risk of mold and mildew.

The LP091CEM-Y8 incorporates a user-friendly interface that includes an easy-to-read LED display. Users can adjust the temperature and settings using the included remote control, providing added convenience. The unit also features multiple fan speeds, allowing users to customize airflow according to their personal preferences.

A standout technological aspect of this model is its Energy Efficiency Ratio (EER), which provides a measure of its cooling efficiency. The LP091CEM-Y8 is designed to operate efficiently, reducing energy consumption while still delivering powerful cooling performance. This energy-saving feature not only helps lower utility bills but also makes the unit an environmentally friendly option.

Additionally, the LP091CEM-Y8 is equipped with a programmable timer, enabling users to set specific operating times. This feature allows the air conditioner to automatically turn on or off based on the user’s schedule, providing a seamless cooling experience. The unit also includes a washable and reusable air filter, which helps to improve indoor air quality by capturing dust and allergens.

Moreover, its compact and portable design includes caster wheels, making it easy to move the unit from room to room. The sleek and modern aesthetic ensures that it fits well with a variety of interior decors.

In summary, the LG Electronics LP091CEM-Y8 is a powerful, efficient, and user-friendly portable air conditioning unit that provides excellent cooling and convenience. Its advanced features, including a high BTU rating, energy efficiency, and easy mobility, make it an outstanding choice for anyone looking to enhance their indoor comfort.
Top Page Image Contents