LG Electronics EN 61000-2, EN 61000-3 Norm) Cooling operation, Gentle Breeze by the Chaos logic

Page 14

Operating Instruction

Cooling operation

1

Press the Start/Stop button.

The unit will respond with

a beep.

2

Open the door of the remote controller. To select Cooling

Operation, press the Operation Mode Selection button.

Each time the button is pressed, the operation mode is shifted in the direction of the arrow.

Cooling

Auto

Healthy

Heating

 

 

Dehumidification

(Heat pump model only)

3

Close the door of the remote controller. Set the temperature

lower than the room temperature. The temperature can be

 

set within a range of 18°C~30°C(64°F~86°F) at intervals of

 

1°C(2°F).

ON

To raise the temperature

 

 

To lower the temperature

4

Set the fan speed again with the door

of the remote controller still closed.

You can select the fan speed in four steps-low, medium, high and CHAOS. Each time the button is pressed, the fan speed mode is shifted.

Gentle Breeze by the CHAOS logic

❏For fresher feeling, press the Indoor fan speed selector and set to CHAOS mode. In this mode, the wind blows like a natural breeze by automatically changing fan speed according to the CHAOS logic.

14Room Air Conditioner

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Room Air Conditioner Table of Contents Be sure not to do Be sure to follow the instruction Safety PrecautionsDo not use damaged power cords, plugs, or a loose socket Do not allow water to run into electric part Do not handle the pipe by yourselfCostomerUse a dedicated outlet for this appliance Appliances near the power CableThere is risk of fire or electrical shock Performing cleaning or Used for a long time MaintenanceUnplug the appliance before Low refrigerant levels may cause product failureProduct Avoid personal injuryThis could damage your health There is risk of personal injuryThere is risk of fire or explosion Replace all the batteries in the remoteBe careful and avoid personal injury They may burn or explodePrior To Operation Cleaning And MaintenanceService Preparing For OperationIntroduction Symbols Used In This ManualFeatures IndoorElectrical Safety Operating Instruction How To Insert The BatteriesStorage And Tips For Using The Remote Controler Remote Control Operations ControlsCooling operation Gentle Breeze by the Chaos logicAuto operation During Auto OperationHealthy dehumidification operation During Healthy Dehumidification OperationRemote controller still closed. You can Close the door of the remote controllerTemperature can be set within a range Heating operation Heat pump model onlyJet cool operation Or orNEO Plasma purification operationOptional NEO Plasma Air Purifying Operation only2nd F operation Button is pressed againSetting the time Additional FeaturesSleep mode Delay start/Pre-set stopTo adjust left/rightHorizontal Airflow direction Vertical Airflow Direction ControlTest operation Auto clean OptionalForced operation Display Luminosity Optional To disable functionTo enable function Auto restartMaintenance And Service Indoor UnitAir conditioner does not operate Before calling for serviceAir does not feel cold enough on the cooling setting Side Air intake vents Air outlet vents Rear PipingAir conditioner does not start TroubleshootingAir conditioner may be operating abnormally when Fuse is blown/circuit breaker is trippedMemo No A20434L
Related manuals
Manual 28 pages 56.67 Kb

EN 61000-3 Norm), EN 61000-2 specifications

LG Electronics is committed to delivering cutting-edge technology while ensuring compliance with international standards. Among these standards are the EN 61000-2 and EN 61000-3 norms, which address electromagnetic compatibility (EMC) and are critical in defining how electrical and electronic devices interact with their electromagnetic environment.

EN 61000-2 focuses on the environment within which devices operate. This standard outlines the general requirements for the compatibility of various electrical devices in residential, commercial, and industrial environments. It specifies the necessary electromagnetic interference (EMI) levels to protect devices from disturbances that could impact their functionality. For LG Electronics, adherence to EN 61000-2 means engineering products that minimize the potential for EMI disruptions, thereby ensuring reliable performance in diverse settings.

On the other hand, EN 61000-3 addresses the emission limits for harmonic currents in electrical systems and equipment. It focuses on ensuring that devices do not generate excessive current harmonics that could disrupt the normal operation of other equipment. For LG, compliance with EN 61000-3 involves implementing technologies that reduce harmonic distortion, which improves the overall power quality in electrical systems. This aspect is particularly important for ensuring energy efficiency and enhancing the longevity of both LG products and the systems they are integrated into.

One of the main features of LG’s products that adhere to these standards is the incorporation of advanced filtering technologies. These filters are designed to suppress harmful electromagnetic emissions and ensure that devices operate within permissible limits. Furthermore, LG employs superior circuit designs that prioritize efficient power management, helping to minimize harmonic generation.

Moreover, LG’s commitment to sustainability is reflected in its adherence to these norms. By reducing electromagnetic emissions and improving power quality, LG Electronics not only complies with regulations but also contributes to a greener environment. This aligns with the company’s broader vision of producing environmentally friendly and energy-efficient products.

In summary, LG Electronics continuously invests in technologies that ensure compliance with EN 61000-2 and EN 61000-3 norms. Through advanced filtering solutions and efficient circuit designs, the company demonstrates its dedication to electromagnetic compatibility, reliability, and sustainability, reinforcing its position as a leader in the global electronics market.
Top Page Image Contents