LG Electronics EN 61000-3 Norm), EN 61000-2 owner manual NEO Plasma purification operationOptional

Page 19

Operating Instruction

NEO PLASMA purification operation(Optional)

1

Press the Start/Stop button.

The unit will respond with a

beep.

2

Open the door of the remote

controller. Press the PLASMA

button.

Operation will start when the button is pressed and stop when the button is pressed again.

Set the fan speed again with the door of the remote

3 controller closed. You can select the fan speed in four steps-low, medium, high or CHAOS. Each time the button is pressed, the fan

speed mode is shifted.

Air purifying operation (NEO PLASMA) can be with cooling, Heating or any other operations.

ENGLISH

NEO PLASMA Air Purifying Operation only

If you press the only PLASMA button, only

PLASMA purification function operates.

Then, fan speed is low. You can select the fan speed in four steps-low, medium, high or

CHAOS.

Each time the Indoor Fan Speed Selector button is pressed, the fan speed mode is shifted.

Owner’s Manual 19

Image 19
Contents Room Air Conditioner Table of Contents Do not use damaged power cords, plugs, or a loose socket Safety PrecautionsBe sure not to do Be sure to follow the instruction Use a dedicated outlet for this appliance Do not handle the pipe by yourselfCostomerDo not allow water to run into electric part Cable Appliances near the powerLow refrigerant levels may cause product failure Performing cleaning or Used for a long time MaintenanceUnplug the appliance before There is risk of fire or electrical shockThere is risk of personal injury Avoid personal injuryThis could damage your health ProductThey may burn or explode Replace all the batteries in the remoteBe careful and avoid personal injury There is risk of fire or explosionPreparing For Operation Cleaning And MaintenanceService Prior To OperationIndoor Symbols Used In This ManualFeatures IntroductionElectrical Safety Storage And Tips For Using The Remote Controler How To Insert The BatteriesOperating Instruction Controls Remote Control OperationsGentle Breeze by the Chaos logic Cooling operationDuring Auto Operation Auto operationDuring Healthy Dehumidification Operation Healthy dehumidification operationHeating operation Heat pump model only Close the door of the remote controllerTemperature can be set within a range Remote controller still closed. You canOr or Jet cool operationNEO Plasma Air Purifying Operation only NEO Plasma purification operationOptionalButton is pressed again 2nd F operationDelay start/Pre-set stop Additional FeaturesSleep mode Setting the timeVertical Airflow Direction Control To adjust left/rightHorizontal Airflow directionForced operation Auto clean OptionalTest operation Auto restart To disable functionTo enable function Display Luminosity OptionalIndoor Unit Maintenance And ServiceSide Air intake vents Air outlet vents Rear Piping Before calling for serviceAir does not feel cold enough on the cooling setting Air conditioner does not operateFuse is blown/circuit breaker is tripped TroubleshootingAir conditioner may be operating abnormally when Air conditioner does not startMemo No A20434L
Related manuals
Manual 28 pages 56.67 Kb

EN 61000-3 Norm), EN 61000-2 specifications

LG Electronics is committed to delivering cutting-edge technology while ensuring compliance with international standards. Among these standards are the EN 61000-2 and EN 61000-3 norms, which address electromagnetic compatibility (EMC) and are critical in defining how electrical and electronic devices interact with their electromagnetic environment.

EN 61000-2 focuses on the environment within which devices operate. This standard outlines the general requirements for the compatibility of various electrical devices in residential, commercial, and industrial environments. It specifies the necessary electromagnetic interference (EMI) levels to protect devices from disturbances that could impact their functionality. For LG Electronics, adherence to EN 61000-2 means engineering products that minimize the potential for EMI disruptions, thereby ensuring reliable performance in diverse settings.

On the other hand, EN 61000-3 addresses the emission limits for harmonic currents in electrical systems and equipment. It focuses on ensuring that devices do not generate excessive current harmonics that could disrupt the normal operation of other equipment. For LG, compliance with EN 61000-3 involves implementing technologies that reduce harmonic distortion, which improves the overall power quality in electrical systems. This aspect is particularly important for ensuring energy efficiency and enhancing the longevity of both LG products and the systems they are integrated into.

One of the main features of LG’s products that adhere to these standards is the incorporation of advanced filtering technologies. These filters are designed to suppress harmful electromagnetic emissions and ensure that devices operate within permissible limits. Furthermore, LG employs superior circuit designs that prioritize efficient power management, helping to minimize harmonic generation.

Moreover, LG’s commitment to sustainability is reflected in its adherence to these norms. By reducing electromagnetic emissions and improving power quality, LG Electronics not only complies with regulations but also contributes to a greener environment. This aligns with the company’s broader vision of producing environmentally friendly and energy-efficient products.

In summary, LG Electronics continuously invests in technologies that ensure compliance with EN 61000-2 and EN 61000-3 norms. Through advanced filtering solutions and efficient circuit designs, the company demonstrates its dedication to electromagnetic compatibility, reliability, and sustainability, reinforcing its position as a leader in the global electronics market.