Leakage Checkpoints, Service | State Industries GS675YRVIT specs

Service

If a condition persists or you are uncertain about the operation of the water heater contact a service agency.

Use this guide to check a “Leaking” water heater. Many suspected “Leakers” are not leaking tanks. Often the source of the water can

be found and corrected.

If you are not thoroughly familiar with gas codes, your water heater, and safety practices, contact your gas supplier or qualified installer

to check the water heater.

Read this manual first. Then before checking the water heater make sure the gas supply has been turned “OFF”, and never turn the gas “ON” before the tank is completely full of water.

LEAKAGE CHECKPOINTS

Never use this water heater unless it is completely filled with water. To prevent damage to the tank, the tank must be filled with water.

BWater must flow from the hot water faucet before turning “ON” gas to the water heater.

	A	*Condensation may be seen on pipes in humid weather or pipe
D		connections may be leaking.
D
	B. *The anode rod fitting may be leaking.
C	C. Small amounts of water from temperature-pressure relief valve

		may be due to thermal expansion or high water pressure in your
		area.
	D. *The temperature-pressure relief valve may be leaking at the
		tank fitting.
	E. Water from a drain valve may be due to the valve being slightly
		opened.
	F. *The drain valve may be leaking at the tank fitting.
F	G. Combustion products contain water vapor which can condense
	G	on the cooler surfaces of the tank. Droplets form and drip onto
	G	the burner or run on the floor. This is common at the time of

E		start-up after installation and when incoming water is cold.
	H. Water in the water heater bottom or on the floor may be from
		condensation, loose connections, or the relief valve. DO NOT
		replace the water heater until a full inspection of all possible
		water sources is made and necessary corrective steps taken.
	Leakage from other appliances, water lines, or ground seepage
	should also be checked.
	*	To check where threaded portion enters tank, insert cotton
		swab between jacket opening and fitting. If cotton is wet, follow
		“Draining” instructions in the “Periodic Maintenance” section and

then remove fitting. Put pipe dope or teflon tape on the threads and replace. Then follow “Filling the Water Heater” instructions in the “Installing the New Water Heater” section.

GS675HRVIT, GS675YRVIT specifications

The State Industries GS675HRVIT and GS675YRVIT are high-efficiency water heaters designed to meet the growing demand for reliable and energy-efficient hot water solutions. These models are ideal for both residential and light commercial applications, offering a blend of advanced technology, durable construction, and user-friendly features.

One of the standout characteristics of the GS675HRVIT and GS675YRVIT is their compact design, which makes them easy to install in various spaces without compromising performance. Both units are equipped with a high-efficiency gas burner that provides rapid water heating capabilities. Their power input allows for quick recovery rates, ensuring a steady supply of hot water when needed.

Energy efficiency is a key feature of these models. They utilize advanced insulation materials and designs that minimize heat loss, thus significantly reducing energy consumption. This not only contributes to lower utility bills but also supports environmental sustainability efforts by lowering carbon footprints. Both models are designed to meet or exceed Energy Star certification standards, highlighting their commitment to energy conservation.

In terms of technology, the GS675HRVIT and GS675YRVIT incorporate robust safety features, including a temperature and pressure relief valve that prevents dangerous pressure build-up, as well as an electronic ignition system that improves reliability by eliminating the need for a standing pilot light. Additionally, the gas control valve ensures precise regulation of the water temperature, enhancing safety and comfort for users.

Durability is another hallmark of these water heaters. Constructed with high-quality materials, the units feature a glass-lined tank that resists corrosion, extending the lifecycle of the product. They also come with a comprehensive warranty, providing peace of mind for consumers regarding their investment.

Users will appreciate the convenience that the GS675HRVIT and GS675YRVIT models offer, including easy-to-use controls and clear indicators for operational status. Installation and maintenance are simplified, making it straightforward for both homeowners and professionals to manage the unit over time.

Overall, State Industries GS675HRVIT and GS675YRVIT are excellent choices for anyone looking for efficient, reliable, and durable water heating solutions. With their innovative technology, energy-saving features, and user-friendly design, these models stand out in the competitive market of hot water heaters.