Pella 81AK0101 installation instructions Interior Finishing, Finishing Instructions

Page 16

INTERIOR FINISHING

If products cannot be finished immediately, cover with clear plastic to protect from dirt, damage and moisture. Remove any construction residue before finishing. Sand all wood surfaces lightly with 180 grit or finer sandpaper. DO NOT use steel wool. BE CAREFUL NOT TO SCRATCH THE GLASS. Remove sanding dust.

Pella products must be finished per the below instructions; failure to follow these instructions voids the Limited Warranty.

FINISHING INSTRUCTIONS

Paint or finish immediately after installation.

Note: DO NOT paint, stain or finish weatherstrip or vinyl parts! If paint, stain or finish gets on the weatherstripping, wipe it off immediately with a damp cloth. To maintain proper performance, do not remove weatherstrip, foam corner seal wedges or gaskets. Air and water leakage may result if these factory-installed items are removed. After finishing, allow doors to dry completely before closing them. Pella will not be responsible for finishing imperfections. The use of unapproved finishes, solvents or cleaning chemicals may cause adverse reactions with door materials. Pella will not be responsible for problems caused by the use fo unapproved materials. If in doubt, contact your local retailer or representative.

Use of inappropriate finishes, solvents, brickwash or cleaning chemicals will cause adverse actions with window and door materials and voids the Limited Warranty.

Care and maintenance information is available in the Pella Owner's Manual. You can obtain an owner's manual by contacting your local Pella retailer. This information is also available on www. pella.com.

Factory Prefinished Panels: A door panel that has been prefinished with stain or paint from the factory requires no additional finishing. Clean the surface with mild soap and water. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.

Clad Exterior Frame: The exterior frame is protected by aluminum cladding with our tough EnduraClad® baked-on-factory finish that needs no painting. Clean this surface with mild soap and water. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.

Panel Cleaning and Prep Instructions for Unfinished or Primed Panels: Dry wipe dust from doors gently. Examine door for possible smudges or fingerprints made from normal handling or construction. To remove smudges, lightly wipe surface with warm water. DO NOT sand surface of fiberglass panel. Scuff sand with light grade sand paper or abrasive pad (220 grit or higher). Rinse surface with mineral spirits for fiberglass panels and warm water for steel panels. Let door and sidelight surfaces dry completely before applying finish. Finish the door panels as soon as possible after installation.

Staining fiberglass panels or unfinished interior frame members: Fiberglass door and sidelight panels may be stained with a gel stain if a wood look is desired. Pella offers stain kits in a variety of colors. Apply and finish per the stain kit manufacturer's instruction. Ensure that all exposed panel edges are finished to minimize the chance of damage. Unprimed interior frame parts may be stained with wood stains and should be finished with a minimum of two coats of a clear polyurethane finish. DO NOT bridge the top coat between the outer edge of the glazing frame and the door panel.

Note: The fiberglass base color tone will vary. This variance is normal and will not impact the stain color of the door.

Painting Instructions: Wood door frame exteriors, premium steel door panels and sidelights are factory primed. If a paint finish is desired, finish the parts with two coats of a 100% latex paint that has a good blocking resistance. On units with glass, do not bridge paint between the outer edges of the glazing frame and the door panel. On fiberglass products, brush the paint in the same direction as the simulated wood grain. Ensure that all exposed panel edges are finished to minimize the change of panel damage.

Failure to use the correct type of finish may result in a door that sticks shut. Ask a qualified paint professional to specify a product with good blocking resistance.

On patio doors: It is optional to paint, stain or finish the vertical and horizontal panel edges.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Remember to USE Appropriate Personal Protective Equipment YOU will Need to Supply Rough Opening PreparationTools Required Rough Opening Preparation For Doors Using Optional Sill PAN GO to StepGO to Step Optional Sill Pan Instructions Prepare the Door for Installation Setting and Fastening the Door 3EDSetting and Fastening the Door Clip or Frame Screw INSTALLATION, GO to StepBetween the door panel and door frame. Additional Integrating the Door to the Water Resistive Barrier Integrating the Door to the Water Resistive Barrier Head Flashing Instruction and Rough Opening PreparationDoor Replacement in Siding Without Nail FIN For Sill Preparation see steps 1E 1TAlternate Anchoring METHODS, Clip and Screw Placement Installation Clip Method Door Replacement in SidingWithout Nail FIN Frame Screw Method Interior Seal Sealing the Door to the Exterior Wall Cladding Interior Finishing Finishing InstructionsCare and Maintenance Important Notice Exterior FinishingTroubleshooting Adjustable Strike Latching Issues Issue

81AK0101 specifications

The Pella 81AK0101 is an innovative window solution designed to provide both aesthetic appeal and functional efficiency. Known for its remarkable blend of style, durability, and energy efficiency, this window model is ideal for homeowners seeking to enhance their living spaces while minimizing energy costs.

One of the standout features of the Pella 81AK0101 is its energy efficiency. The window is designed with multiple layers of insulating glass, which significantly reduce heat transfer. This is complemented by low-E (low-emissivity) glass coatings that reflect heat during the summer months and retain warmth during the winter, making it suitable for diverse climates. The dual-pane construction further enhances the window's performance, minimizing condensation and improving thermal performance.

Another exceptional characteristic of the Pella 81AK0101 is its durability. Constructed with high-quality materials, these windows are built to withstand the elements, ensuring long-lasting performance. The fusion-welded vinyl frames provide added strength and resistance against warping, cracking, and fading. This durability translates to lower maintenance costs and longer lifespans, making Pella windows a smart investment for homeowners.

In terms of design, the Pella 81AK0101 offers a wide array of style options to fit various home aesthetics. From traditional to modern, these windows can be customized with various finishes, colors, and grid patterns. Homeowners can choose between various configurations, such as single-hung, double-hung, or sliding styles, allowing for increased versatility in design.

Safety features are also a top priority with the Pella 81AK0101. It includes advanced locking mechanisms that enhance security, providing peace of mind for homeowners. Additionally, the laminated glass option is available for those wishing to enhance safety further, as it helps prevent shattering and minimizes the risk of injury.

Overall, the Pella 81AK0101 window model stands out as an exceptional choice for energy efficiency, durability, and design flexibility. With its commitment to quality and innovation, Pella continues to be a respected name in the window industry. Homeowners looking to enhance their spaces while enjoying significant energy savings will find the Pella 81AK0101 an excellent addition to their homes.
Top Page Image Contents