Multiquip MC3SEA, MC3PBA (B&S), MC3SBA (B&S), MC3PEA manual Mixer Safety

Page 8
DANGEROUS
GAS FUMES

MIXER SAFETY

DANGER

„NEVER operate the equipment in an explosive atmosphere or near combustible materials.An explosion or fire could result causing severe bodily harm or even death.

„DO NOT mix flammable or explosive substances.

WARNING

„ NEVER place your hands inside the drum while starting or operating this equipment.

„ NEVER disconnect any emergency or safety devices. These devices are

intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

„Before operating mixer, ensure that safety grate is in position and correctly fitted.

CAUTION

„NEVER lubricate components or attempt service on a running machine.

NOTICE

„ALWAYS keep the machine in proper running condition.

„ALWAYS ensure mixer is on level ground before mixing.

„Fix damage to machine and replace any broken parts immediately.

„DO NOT tip mixer onto drum mouth when the drum is rotating.

„Ensure the drum is rotating while filling and emptying the drum.

„ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

SAFETY INFORMATION

ENGINE SAFETY (GASOLINE MODELS ONLY)

DANGER

„Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.

„The engine of this equipment requires an adequate free flow of cooling air. NEVER operate this equipment in any enclosed or narrow

area where free flow of the air is restricted. If the air

flow is restricted it will cause injury to people and property and serious damage to the

equipment or engine.

WARNING

„DO NOT place hands or fingers inside engine compartment when engine is running.

„NEVER operate the engine with heat shields or guards removed.

„Keep fingers, hands hair and clothing away

from all moving parts to prevent injury.

„DO NOT remove the engine oil drain plug

while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the mixer.

CAUTION

„NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool

before servicing equipment.

„Make certain the operator knows how to and is capable of turning the engine OFF in case of an emergency.

NOTICE

„NEVER run engine without an air filter or with a dirty air filter. Severe engine damage may occur. Service air filter frequently to prevent engine malfunction.

„NEVER tamper with the factory settings of the engine or engine governor. Damage to the engine or equipment can result

if operating in speed ranges above the maximum allowable.

PAGE 8 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11)

Page 7 Page 9
Image 8
Page 7 Page 9
Contents MIX N GO Proposition 65WARNING SILICOSIS/RESPIRATORWARNINGS Silicosis WarningTable of Contents Order via Fax Dealers Only Parts Ordering ProceduresBest Deal! Order via Internet Dealers Only Safety Information Safety MessagesGeneral Safety Mixer Safety Fuel Safety Gasoline Models only Transporting Safety Operation and Safety Decals Machine Safety DecalsOperation and Safety Decals Advertencia AvertissementMIX N GO Mixer Specifications Dimensions L x W x HDry Net Weight ModelMIX N GO Mixer Dimensions Mixer MIX N GO Mixer Dimensions Electric Motor MIX N GO Mixer General Information MIX N GO Mixer Mixer Components Mixer ComponentsMIX N GO Mixer Basic Engine Engine Controls and ComponentsAssembly Packing ContainerMIX N GO Mixer Assembly Instructions Before Starting Engine Oil CheckFuel Check Belt CheckMIX N GO Mixer Initial START-UP Electric Motor Initial Start-up Instructions Electric Motor StartingStarting the Engine Briggs & Stratton Engine Choke Lever ClosedMIX N GO Mixer Initial START-UP Gasoline Engine Stopping The EngineMIX N GO Mixer Maintenance Maintenance Gearbox Oil CheckMIX N GO Mixer Maintenance Gasoline Engine Engine Maintenance ScheduleEngine Air Cleaner Spark Plug GapMIX N GO Mixer Preparation for Long -TERM Storage MIX N GO Mixer Operation and Parts Manual REV. #3 09/20/11 MIX N GO Mixer Troubleshooting Engine Engine TroubleshootingMIX N GO Mixer Troubleshooting ENGINE/MIXER MIX N GO Mixer Explanation of Code in Remarks Column QTY. ColumnMIX N GO Mixer Suggested Spare Parts To 3 UnitsMIX N GO Mixer Name Plate and Decals Name Plate and DecalsDecalwarning MQ 26B MIX N GO Mixer Mixer ASSY. Steel Drum Remarks26B Part Name QTY Remarks MIX N GO Mixer Mixer ASSY. Plastic Drum Belt Guard MIX N GO Mixer Mixer ASSY. Plastic Drum Plastic Barrel Terms and Conditions of Sale Parts Freight PolicyMIX N GO Mixer Operation and Parts Manual REV. #3 09/20/11 HERE’S HOW to GET Help

MC3PEA, MC3PBA (B&S), MC3SBA (B&S), MC3SEA specifications

The Multiquip MC3 series is a line of high-performance concrete power trowels, especially designed to improve surface finishing, enhancing both efficiency and quality in various construction projects. The MC3SEA, MC3SBA (B&S), MC3PBA (B&S), and MC3PEA models offer advanced technologies and features that cater to the needs of different applications.

One of the standout features of the MC3 series is its robust construction. Each model is built with a heavy-duty steel frame, ensuring durability and longevity in demanding environments. The trowels are engineered to withstand rigorous use while providing excellent stability during operation, which is critical for achieving a smooth finish on concrete surfaces.

Powering these machines are reliable engine options, with the B&S (Briggs & Stratton) engines integrated into the MC3SBA and MC3PBA models. These engines are known for their fuel efficiency and ease of maintenance, making them an optimal choice for contractors seeking reliable performance. The MC3SEA and MC3PEA models offer alternative engine configurations tailored for specific applications, providing contractors with choices that best suit their work demands.

The torque capabilities of the MC3 series are impressive, allowing for effective power transfer to the trowel blades. This results in a thorough finishing process, enhancing the evenness of concrete surfaces. The trowels come with various blade options, including both standard and extended blades, enabling operators to customize their equipment based on job requirements.

The ergonomics of the MC3 series have been designed with user comfort in mind. Equipped with padded handles and adjustable operating positions, operators can work for extended periods without experiencing fatigue. The intuitive control layout enhances maneuverability, allowing for precise handling in tight spaces.

Another key characteristic of the MC3 series is its easy maintenance. With accessible engine compartments and straightforward service points, routine maintenance tasks can be performed with minimal downtime, ensuring that contractors can keep their projects on schedule.

In summary, the Multiquip MC3SEA, MC3SBA (B&S), MC3PBA (B&S), and MC3PEA power trowels represent a blend of power, durability, and user-friendliness. Their robust construction, versatile engine options, ergonomic design, and easy maintenance make them ideal choices for concrete finishing tasks, providing contractors with the reliability and performance needed to achieve high-quality results on the job site.
Top Page Image Contents