Pella 812W0100 Interior Finishing, Exterior Finish, Care and Maintenance Important Notice, Pella

Page 10

INTERIOR FINISHING

If products cannot be finished immediately, cover with clear plastic to protect from dirt, damage and moisture. Remove any construction residue before finishing. Sand all wood surfaces lightly with 180 grit or finer sandpaper. DO NOT use steel wool. BE CAREFUL NOT TO SCRATCH THE GLASS. Remove sanding dust.

Pella products must be finished per the below instructions; failure to follow these instructions voids the Limited Warranty.

•On casement and awnings, it is optional to paint, stain or finish the vertical and horizontal sash edges.

•On single-hung and double-hung, do not paint, stain or finish the vertical sash edges, any finish on the vertical sash edges may cause the sash to stick; it is optional to paint, stain or finish the horizontal sash edges.

•On patio doors, it is optional to paint, stain or finish the vertical and horizontal panel edges.

Note: To maintain proper product performance do not paint, finish or remove the weather- stripping, mohair dust pads, gaskets or vinyl parts. Air and water leakage will result if these parts are removed. After finishing, allow venting windows and doors to dry completely before closing them.

Pella Corporation is not responsible for interior paint and stain finish imperfections for any product that is not factory-applied by Pella Corporation. Use of inappropriate finishes, solvents, brickwash, or cleaning chemicals will cause adverse reactions with window and door materials and voids the Limited Warranty.

For additional information on finishing see the Pella Owner's Manual or go to www.pella.com.

EXTERIOR FINISH

The exterior frame and sash are protected by aluminum cladding with our tough EnduraClad® or EnduraClad Plus baked-on factory finish that needs no painting. Clean this surface with mild soap and water. Stubborn stains and deposits may be removed with mineral spirits. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.

Use of inappropriate finishes, solvents, brickwash or cleaning chemicals will cause adverse reactions with window and door materials and voids the Limited Warranty.

CARE AND MAINTENANCE

Care and maintenance information is available in the Pella Owner’s Manual. You can obtain an owner’s manual by contacting your local Pella retailer. This information is also available on

www.pella.com.

IMPORTANT NOTICE

Because all construction must anticipate some water infiltration, it is important that the wall

system be designed and constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipated water infiltration; deficiencies in building design, construction and maintenance; failure to install Pella products in accordance with Pella’s installation instructions; or the use of Pella products in wall systems which do not allow for proper management of moisture within the wall systems. The determination of the suitability of all building components, including the use of Pella products, as well as the design and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect, contractor, installer, or other construction professional and are not the responsibility

of Pella.

Pella products should not be used in barrier wall systems which do not allow for proper management of moisture within the wall systems, such as barrier Exterior Insulation and Finish Systems, (EIFS) (also known as synthetic stucco) or other non-water managed systems. Except in the states of California, New Mexico, Arizona, Nevada, Utah, and Colorado, Pella makes no warranty of any kind on and assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the states listed above, the installation of Pella Products in barrier wall or similar systems must be in accordance with Pella’s installation instructions.

Product modifications that are not approved by Pella Corporation will void the Limited Warranty.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Part Number 812W0100 Measure all four sides of the opening to make Rough Opening PreparationVerify the window will fit the opening BowedRough Opening Preparation Setting and Fastening the WindowApply sill flashing tape #2. Cut a piece of flashing tape Setting and Fastening the Window To hold the window in place while shimming it plumb SquarePoints around the window Apply side flashing tape. Cut two pieces of flashing Integrating the Window to the Water Resistive BarrierRectangular Units Only Overlapping tape down, and press all tape downIntegrating the Window to the Water Resistive Barrier Sheathing. On the short side of aInterior Seal Sealing the Window to the Exterior Wall CladdingSealing the Window to the Exterior Wall Cladding Additional cutting patternsExterior Finish Care and Maintenance Important NoticeInterior Finishing PellaInstalling Roto Cover and Crank Lock Lever Removal and Insertion

812W0100 specifications

The Pella 812W0100 is a high-performance window that embodies innovative engineering and advanced technology, ensuring it meets the diverse needs of modern homeowners. Designed for both aesthetics and functionality, this product stands out as a premier choice for new constructions and renovations alike.

One of the primary features of the Pella 812W0100 is its energy efficiency. This window is equipped with advanced Low-E glass that reflects heat in the summer and retains warmth in the winter. This technology significantly enhances thermal insulation, helping to reduce heating and cooling costs throughout the year. The Pella 812W0100 also comes with multiple glazing options, allowing homeowners to customize their window’s energy performance according to their climate and specific needs.

In terms of durability, the Pella 812W0100 boasts a robust frame made from high-quality materials that resist warping, cracking, and fading. The window is constructed with a unique fiberglass and composite blend that provides long-lasting strength and stability, making it an excellent choice for areas with extreme weather conditions. Additionally, the window's exterior is designed to withstand harsh elements without compromising its appearance.

The design of the Pella 812W0100 offers versatility that caters to various architectural styles. Available in multiple colors and finishes, homeowners can choose options that seamlessly blend with their home’s exterior and interior decor. The window's sleek lines and large viewing area maximize natural light while providing unobstructed views of the outdoors.

For added convenience, the Pella 812W0100 features an easy-to-use locking system that enhances security without sacrificing style. The window operates smoothly, thanks to its precision-engineered hardware, ensuring long-term reliability.

Installation and maintenance of the Pella 812W0100 are also streamlined. This window is designed for easy installation, reducing labor costs and time spent during the building process. Furthermore, its low-maintenance exterior simply requires periodic cleaning to keep it looking fresh and new.

Ultimately, the Pella 812W0100 combines cutting-edge technology, energy efficiency, aesthetic appeal, and robust durability, making it an ideal choice for homeowners looking to enhance their living spaces while optimizing energy savings and security.
Top Page Image Contents