Pella 80ED0101 Sealant line, Apply a bead of high quality exterior grade sealant to

Page 8

A. Insert backer rod into the space around the window

 

APPROXIMATELY  4HIS SHOULDSPROVIDE ATELEASTTA  A

 

clearance between the backer rod and the exterior face

 

of the window.

 

Note: Backer rod adds shape and depth for the

8A

sealant line.

 

B. Apply a bead of high quality exterior grade sealant to

 

the entire perimeter of the window.

 

C. Shape, tool and clean excess sealant. When finished, the

8B

 

sealant should be the shape of an hourglass.

 

Note: This method creates a more flexible sealant line

 

capable of expanding and contracting.

 

INTERIOR FINISHING

If products cannot be finished immediately, cover with clear plastic to protect from dirt, damage and moisture. 2EMOVEEANYACONSTRUCTION RESIDUE BEFOREElNISHINGS3ANDNALL WOOD SURFACESCLIGHTLYLWITH  GRIT OR lNERHSANDPAPER $/ ./44USEUSTEEL WOOLE"% #!2%&5, ./444//3#2!4#( 4(%(',!33 2EMOVEESANDINGNDUST

Pella products must be finished per the below instructions; failure to follow these instructions voids the Limited Warranty.

ss/NNCASEMENT AND AWNINGS AIT IS OPTIONAL TOGPAINT STAIN ORSlNISHSTHE VERTICALCANDLHORIZONTALTSASH EDGES ss/NNSINGLEHUNGLANDDOUBLEHUNG DODNOTDPAINT STAIN ORUlNISH THEHVERTICALCSASH EDGES SANY lNISHGON THE VERTICALC A

SASHSEDGESHMAYECAUSEETHE SASH TO STICK ITEIS OPTIONALSTO PAINT STAIN ORTlNISHNTHEOHORIZONTALTSASH EDGES ss/NNPATIOADOORS ITDIS OPTIONAL TO PAINT SSTAINPOR lNISH THE VERTICALCANDLHORIZONTALTPANEL EDGES

Note: To maintain proper product performance do not paint, finish or remove the weather-stripping, mohair dust pads, gaskets or vinyl parts. Air and water leakage will result if these parts are removed. After finishing, allow venting windows and doors to dry completely before closing them.

Pella Corporation is not responsible for interior paint and stain finish imperfections for any product that is not factory-applied by Pella Corporation. Use of inappropriate finishes, solvents, brickwash, or cleaning chemicals will cause adverse reactions with window and door materials and voids the Limited Warranty.

For additional information on finishing see the Pella Owner’s Manual or go to www.pella.com.

EXTERIOR FINISH

The exterior frame and sash are protected by aluminum cladding with our tough EnduraClad® or EnduraClad Plus baked-on factory finish that needs no painting. Clean this surface with mild soap and water. Stubborn stains and deposits may be removed with mineral spirits. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.

Use of inappropriate finishes, solvents, brickwash or cleaning chemicals will cause adverse reactions with window and door materials and voids the Limited Warranty.

CARE AND MAINTENANCE

Care and maintenance information is available in the Pella Owner’s Manual. You can obtain an owner’s manual by contacting your local Pella retailer. This information is also available on http://www.pella.com.

IMPORTANT NOTICE

Because all construction must anticipate some water infiltration, it is important that the wall system be designed and constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipated water infiltration; deficiencies in building design, construction and maintenance; failure to install Pella products in accordance with Pella’s installation instructions; or the use of Pella products in wall systems which do not allow for proper management of moisture within the wall systems. The determination of the suitability of all building components, including the use of Pella products, as well as the design and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect, contractor, installer, or other construction professional and are not the responsibility of Pella.

Pella products should not be used in barrier wall systems which do not allow for proper management of moisture within the wall systems, such as barrier Exterior Insulation and Finish Systems, (EIFS) (also known as synthetic

STUCCO COR OTHER NONWATER MANAGED SYSTEMSW%XCEPT INTTHEISTATESSOF #ALIFORNIA .EWW-EXICO !RIZONA .EVADA Utah, and Colorado, Pella makes no warranty of any kind and assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the states listed above, the installation of Pella Products in barrier wall or similar systems must be in accordance with Pella’s installation instructions.

Product modifications that are not approved by Pella Corporation will void the Limited Warranty.

Page 7 Page 8
Image 8
Page 7 Page 8
Contents Important Safety Information Instrucciones en español en el reversoVerify the window will fit the opening Rough Opening PreparationVerify the opening is plumb and level Insert the window from the exterior of the building. Place Setting the WindowPrepare the Window Installation Clip Method Plumb and square windowSimulated-hung only Placement of the frame screwsFrame Screw Method From the room side of the window, DRILLI DIAMETER Reinstall the clad/wood insert and sashesIntegrating the Window to Water Resistive Barrier Interior Seal Sealing the Window to the Exterior Wall CladdingApply flashing tape to diagonal cuts. Cut pieces fin to the interior face of the openingShape, tool and clean excess sealant. When finished, Sealant lineApply a bead of high quality exterior grade sealant to Capable of expanding and contracting

80ED0101 specifications

The Pella 80ED0101 is a remarkable door model that exemplifies Pella's commitment to quality, innovation, and aesthetic appeal. Specifically designed for both residential and commercial applications, this door is intrinsic to enhancing the overall functionality and appearance of an entryway.

One of the standout features of the Pella 80ED0101 is its robust construction. The door is engineered with a sturdy fiberglass exterior, making it highly resistant to warping, cracking, and splitting. This not only results in longevity but also ensures low maintenance over the years, as fiberglass can withstand extreme weather conditions without significant deterioration.

In terms of energy efficiency, the Pella 80ED0101 excels in providing superior insulation. The door includes a core of high-density polyurethane foam, which significantly reduces thermal transfer, keeping interiors comfortable in both hot and cold climates. Furthermore, the door is equipped with double or triple-pane insulated glass options that reduce energy consumption, making the Pella 80ED0101 an environmentally-friendly choice.

Appearance plays a crucial role in entryway selection, and the Pella 80ED0101 does not disappoint. Available in customizable options, homeowners can choose from a variety of finishes, colors, and sizes to fit their specific aesthetic preferences. The door's sleek design can seamlessly blend with various architectural styles, enhancing curb appeal and property value.

Security is also a priority with the Pella 80ED0101. It features an advanced locking system that provides enhanced security against forced entry, making it ideal for protecting homes and businesses. The lock system works in conjunction with a heavy-duty frame and reinforced hinges, ensuring a secure fit in the doorframe.

Moreover, the Pella 80ED0101 is equipped with innovative technologies such as the Easy-Glide roller system for smooth operation in sliding doors and the SmartKey security feature for convenient re-keying of locks.

In summary, the Pella 80ED0101 is a multifaceted door option that combines durability, energy efficiency, aesthetic appeal, and security. Its advanced design and technology cater to the modern homeowner, offering peace of mind and style in one package. With its impressive characteristics, the Pella 80ED0101 stands out as a top choice for anyone looking to enhance their entryways.
Top Page Image Contents