Pella 80ED0101 Frame Screw Method, Placement of the frame screws, Simulated-hung only

Page 5

5 FRAME SCREW METHOD

A. Mark the location of the top of the lower sash on the rough opening.

 

Interior

Note: Marking this location is needed for the correct

placement of the frame screws.

Top of lower sash

 

 

5A

B. Simulated-hung only:

5B

Remove the simulated-hung

Finger slides are

lock by removing the four

located on the

top, back side of

screws from each lock.

the lower sash.

C. Remove the lower sash. Raise the sash 6" or more

and locate the two finger slides on the lower sash5C check rail. At the same time, slide each toward the

center of the sash to disengage the wash lock stops and pull the sash towards the room side. The sash will tilt from the bottom.

D. With the sash parallel to the floor, lift one side of the lower sash until the terminal is removed from the balance shoe. Continue to lift the sash up until the terminal is released from the opposite side of the sash and can be removed from the shoe. Lift the sash up and out of the window frame. Set the sash in a safe location.

E.Simulated-hung and Single-hung only: Remove the screw from the balance shoe in the jamb liner on both jambs.

5E

Lower upper sash

 

6” or more.

Pull the top of the sash to the room side.

5F

Slide the wash lock releases toward the center.

F.Remove the upper sash. Lower the upper sash 6" or more and locate the two wash lock releases on the top of the sash. Slide each toward the center of the sash and pull the top of the sash to the room side.

' With the sash parallel to the floor, lift one side of the upper sash until the terminal is removed from the balance shoe. Continue to lift the sash up until the terminal is released from the opposite side of the sash and can be removed from the shoe. Lift the sash up and out of the window frame. Set the sash in a safe location.

5G

Lift one side of the upper sash until the terminal is removed from the balance shoe.

H. Remove the clad/wood insert. Place a stiff putty knife under the weather- strip between the clad/wood insert and the vinyl on the interior side and gently pry the insert out of the jamb liner.

Note: On taller units, continue to pry up the length of the unit, if needed. Take care not to rip the weather-strip. The top of the insert is

behind the head stop; use care in pulling it down from behind the stop 5H so as not to dent the wood.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Instrucciones en español en el reverso Important Safety InformationVerify the window will fit the opening Rough Opening PreparationVerify the opening is plumb and level Insert the window from the exterior of the building. Place Setting the WindowPrepare the Window Plumb and square window Installation Clip MethodSimulated-hung only Placement of the frame screwsFrame Screw Method From the room side of the window, DRILLI DIAMETER Reinstall the clad/wood insert and sashesIntegrating the Window to Water Resistive Barrier Sealing the Window to the Exterior Wall Cladding Interior SealApply flashing tape to diagonal cuts. Cut pieces fin to the interior face of the openingSealant line Shape, tool and clean excess sealant. When finished,Apply a bead of high quality exterior grade sealant to Capable of expanding and contracting

80ED0101 specifications

The Pella 80ED0101 is a remarkable door model that exemplifies Pella's commitment to quality, innovation, and aesthetic appeal. Specifically designed for both residential and commercial applications, this door is intrinsic to enhancing the overall functionality and appearance of an entryway.

One of the standout features of the Pella 80ED0101 is its robust construction. The door is engineered with a sturdy fiberglass exterior, making it highly resistant to warping, cracking, and splitting. This not only results in longevity but also ensures low maintenance over the years, as fiberglass can withstand extreme weather conditions without significant deterioration.

In terms of energy efficiency, the Pella 80ED0101 excels in providing superior insulation. The door includes a core of high-density polyurethane foam, which significantly reduces thermal transfer, keeping interiors comfortable in both hot and cold climates. Furthermore, the door is equipped with double or triple-pane insulated glass options that reduce energy consumption, making the Pella 80ED0101 an environmentally-friendly choice.

Appearance plays a crucial role in entryway selection, and the Pella 80ED0101 does not disappoint. Available in customizable options, homeowners can choose from a variety of finishes, colors, and sizes to fit their specific aesthetic preferences. The door's sleek design can seamlessly blend with various architectural styles, enhancing curb appeal and property value.

Security is also a priority with the Pella 80ED0101. It features an advanced locking system that provides enhanced security against forced entry, making it ideal for protecting homes and businesses. The lock system works in conjunction with a heavy-duty frame and reinforced hinges, ensuring a secure fit in the doorframe.

Moreover, the Pella 80ED0101 is equipped with innovative technologies such as the Easy-Glide roller system for smooth operation in sliding doors and the SmartKey security feature for convenient re-keying of locks.

In summary, the Pella 80ED0101 is a multifaceted door option that combines durability, energy efficiency, aesthetic appeal, and security. Its advanced design and technology cater to the modern homeowner, offering peace of mind and style in one package. With its impressive characteristics, the Pella 80ED0101 stands out as a top choice for anyone looking to enhance their entryways.
Top Page Image Contents