Desa SL30NT/SL30PT Operating Heater, Installing LOG SET, For Your Safety Read Before Lighting

Page 11

INSTALLATION

Continued

INSTALLING LOG SET

1.Set one-piece log on heater base as shown in Figure 12. Make sure middle section at bottom of log is seated into "U" shaped cutout in center of heater base. Log will fit securely on base. IMPORTANT: Make sure log does not cover any burner ports and does not touch the stove cavity (see Figure 14).

2.Fasten back panel to stove with four (4) bolts and washers re- moved in step 4 of Unpacking, page 6. Make sure product iden- tification label is located on the outside lower left-hand corner.

3.Place freestanding stove in desired position being careful not to damage gas connections. Be sure to maintain clearances to combustibles and wall clearances as outlined on page 7.

 

 

One-Piece

 

 

Log Set

 

 

Middle Section

 

 

at Bottom of

 

 

Log Set

 

 

Burner

 

 

"U" Shaped

Heater

 

Cutout in

FFO

Chassis

Base

 

 

Figure 14 - Installing One-Piece Stove Log Set

Burner Porting Areas (double

One-Pieceslotted rectangular openings Log Set

Safety Pilot

Location

Figure 15 - Top View of One-Piece Log Set on Gas Log Heater

INSTALLATION

11

Installing Log Set

OPERATING HEATER

 

For Your Safety Read Before Lighting

 

Lighting Instructions

 

 

 

OPERATING HEATER

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire de- partment.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service techni- cian or gas supplier. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. Open a window to vent smell. This will only last a few hours.

1.STOP! Read the safety information, abovc.

2.Make sure equipment shutoff valve is fully open.

3. Turn control knob clockwise Clockwise to the OFF position.

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol- low “B” in the safety information, above. If you don’t smell gas, go to the next step.

5. Turn control knob counterclockwise C-clockwiseto the PI-

LOT position. Press in control knob for five (5) seconds (see Figure 16, page 12).

For morevisit www..com

111487-01B

Image 11
Contents What to do if YOU Smell GAS Csbnt Csbpt Cspbnt Cspbpt Cspint CspiptSafety Information Table of ContentsTypical Stove Cabinet Model with Comfort Glow Gas Log Heater Product IdentificationAIR for Combustion and Ventilation Product FeaturesLocal Codes Ventilation Air From Inside Building Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIRStove TOP InstallationUnpacking Ventilation Air From OutdoorsMinimum Wall and Ceiling Clearances see Figure Check GAS TypeClearances to Combustibles Vent-Free Operation Only Installation Items Needed Connecting to GAS SupplyChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Heater Gas Connections Installing ROD and ScreenLighting Instructions Installing LOG SETFor Your Safety Read Before Lighting Operating HeaterTo Turn OFF GAS To Appliance Manual Lighting ProcedureInspecting Burners Thermostat Control OperationLogs Cleaning MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Main BurnerObserved Problem Possible Cause TroubleshootingMaintenance, Observed Problem Possible Cause RemedyTop Accessories SpecificationsService Hints Technical ServiceModels SL30PT and SL30NT Illustrated Parts BreakdownKEY Part Number SL30PT SL30NT Description QTY Parts ListStove Body Models CSB SERIES, Cspb Series Cspi Series KEY Part Number Description QTY FBD Parts CentralsOwners Registration Form Postage Required 111487-01B Warranty Information