Fisher & Paykel CG602 Standards Requirements, Clamping Down the Cooktop, Gas Supply Connection

Page 5

Installation Instructions

Standards Requirements

Australian and New Zealand Gas Installation Standards (AS5601, NZS 5261) require a cooktop to be installed so that the surface temperature of any nearby combustible surface will not exceed 65oC above ambient.

Typically this is achieved by:

A Having the cooktop spaced away from

the wall (see “Clearances” for dimensions)

 

[Dimension c and d]

series

OR

CG902

B by protecting the wall, to at least 150 mm

high [Dimension g] along it’s length, with

non-combustible surface materials, such as:

CG602,

- 5 mm thick ceramic tiles alone are

adequate.

- Tempered glass or sheetmetal (min. 0.4 mm

 

thick) is acceptable when used in front of a

 

fire resistant material.

 

- Fisher & Paykel Splashback (not available

 

in Australia): This is stainless steel with a 10

 

mm air gap to the wall. When used with

 

a 10 mm gap behind the product to the

series

front of the splashback. (Only with SB90

 

series and SB1216 splashbacks.)

CG913

These products meet the Standards

 

requirements when installed to the dimensions in these Instructions. (They have been tested by an Independent Testing Lab).

Clamping Down the Cooktop

This cooktop is supplied with fastening clamps that will cope with a bench thickness of 20-50 mm. For benchtops thicker than 50 mm, recess the underside to a thickness of 20-50 mm.

 

50 mm

20 mm

recessed to

50 mm

 

Gas Supply Connection

This cooktop is supplied set up for Natural Gas but is suitable for installation with either Natural Gas or LPG. Refer to relevant table for pressures and appropriate orifice sizes.

Gas connection to the product MUST use the elbow supplied. The regulator will not seal if installed without it.

Ensure the blue washer (supplied) is located between the elbow (supplied) and product inlet as below. Failure to use this washer will cause the product to leak. Tighten the floating nut to firm finger tight, plus an additional 1/4 turn (90o).

Blue washer

Elbow (1/2” BSP male)

Gas Inlet (1/2” BSP internal thread)

After installation, make sure all connections are gas tight.

A duplicate data plate enclosed inside the accessories pack should be placed on an accessible surface adjacent to the cooktop.

Flexible Hoses

Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified.

Flexible hoses should not be exposed to temperatures exceeding their certified value. They should not touch hot surfaces on the cooktop or neighbouring products.

Flexible hoses should not be subject to abrasion, kinking or permanent deformation.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents NZ & AU Installation InstructionsBefore You Start Safety & WarningsThese products are registered Make the bench top of a heat resistant materialCutout DimensionsProduct CG602 Series CG902 Series CG913 Series ClearancesClearance from side edge 130 mm 120 mm 80 mm Clearance from rear edge 100 mm 90 mmClamping Down the Cooktop Standards RequirementsGas Supply Connection Flexible HosesNatural Gas Gas Supply Connection CheckLP Gas Turn on each gas valve and light each burnerTurn on main electrical supply and light the burners Minimum Setting or Turn DownCheck all burners have good flame see ,4,5 Replace the knobCustomer Care Current Information Gas Rate SummaryCG913TM New Zealand
Related manuals
Manual 17 pages 61.9 Kb Manual 11 pages 35.88 Kb

CG602 specifications

The Fisher & Paykel CG602 is a powerful and stylish gas cooktop that exemplifies the brand's commitment to high-quality kitchen appliances. Designed for home chefs who appreciate both aesthetics and functionality, the CG602 boasts an array of impressive features and technologies, making it a standout choice in the realm of cooking equipment.

One of the main features of the CG602 is its six high-efficiency gas burners, which deliver exceptional heat control and precision for various cooking methods. With a combination of high output and low simmer settings, users can easily sauté, boil, or create a delicate simmer—all with the turn of a knob. Specifically, the cooktop includes a powerful 19MJ/h burner, perfect for rapidly boiling water or achieving high-temperature cooking as well as smaller burners designed for simmering sauces and melting chocolate without the risk of burning.

The CG602 is also designed for ease of use and cleaning. The surface is crafted from durable stainless steel, ensuring longevity while being resistant to stains and scratches. This smooth finish makes it easy to wipe down after cooking, and the minimalistic design reduces the risk of food debris getting trapped in crevices, which is particularly advantageous in busy kitchen environments.

Another technological highlight of the CG602 is its intuitive flame failure safety device, which automatically cuts the gas supply if the flame is extinguished. This feature not only enhances safety while cooking but also promotes peace of mind for users concerned about gas leaks or hazards in the kitchen.

Installation is made effortless as the CG602 is designed for easy integration into various countertop designs. It can be seamlessly installed, whether in a contemporary or more traditional kitchen setting. The unit is also compatible with Fisher & Paykel's extensive range of kitchen appliances, allowing for a cohesive aesthetic in any home.

Additionally, the CG602 features convenient removable burner caps and grates, further simplifying cleaning and maintenance. Ultimately, the Fisher & Paykel CG602 is more than just a functional cooktop; it embodies a philosophy of craftsmanship and innovation, designed for culinary enthusiasts who demand both performance and style. This gas cooktop offers a practical and elegant solution for anyone looking to elevate their cooking experience.
Top Page Image Contents