Fisher & Paykel CG602 installation instructions Gas Supply Connection Check, Natural Gas, LP Gas

Page 6
10 To refit the CG913 series hob tray, repeat steps 6 and 7 in reverse.
11 Check insulation resistance and earth
continuity.continued...
Reset the venturi (see fig.2). Loosen the venturi screw, move the venturi toward the orifice approx. 2 mm.
9
Replace the wok orifice with the correct one using a 10 mm spanner.
8
Lift hob tray from the product.
WARNING!
Cut Hazard.
Beware of sharp edges.
7
6 Remove the 2 screws holding each burner (3 on the wok burner).
Pull off knobs.
Remove all trivets and burner heads.
Ensure all gas valves are turned off.
2
3
4
5 Unscrew the orifices and replace them with the correct ones. (size numbers are stamped on the side, eg. 70= 0.70 mm) (see figure 1)
Turn off the main electrical supply.
WARNING!
Electrical Shock Hazard.
Disconnect product from main power supply before continuing.
1
The operation of the appliance, including the ignition system, must be tested before installation is complete.
If after following the instructions given, satisfactory performance cannot be obtained, contact the local gas authority or your local Approved Service Agent for advice and assistance.
Conversion to Different Gas Type
Burners can be used with NG or LPG, provided that the orifices appropriate for the gas supply are installed.
To change the orifices, you will need a 7 mm box spanner (and a 10 mm ring spanner for CG913TM).

Installation Instructions

Natural Gas

For Natural Gas usage the gas supply is connected to the regulator which is supplied loose with a built in test point - 1kPa (4” WG) and the inlet connection of 1/2 “ B.S.P. (male thread). Do not over tighten.

The test point pressure should be preset to 1.0 kPa with the wok and semi - rapid burners operating at maximum.

LP Gas

For LPG usage the gas supply for the appliance must be regulated to a pressure of 2.75kPa (11” WG). See ‘Conversion to a different gas type’ .

Gas Supply Connection Check

The connection point shall be accessible with the appliance installed.

To enable the gas supply to be readily shut off, the gas supply must be connected with an isolating valve close to the product.

After installation and making all connections check thoroughly for possible leaks.

1 Turn all control knobs on the unit to “off” position.

2 Open the valve on the gas supply.

3 Using a suitable leak detection fluid solution (e.g. Rocol) check each gas connection one at a time by brushing the solution over the connection.

4 The presence of bubbles will indicate a leak. Tighten the fitting and recheck for leaks. Ensure the washer (supplied) is located between elbow and product gas inlet.

5 Turn on each gas valve and light each burner.

6 Check for a clear blue flame without yellow tipping. If burners show any abnormalities, check that they are located and assembled properly. Check correct orifices are installed.

CG913TM only

6

Image 6
Contents Installation Instructions NZ & AUThese products are registered Safety & WarningsBefore You Start Make the bench top of a heat resistant materialDimensions ProductCutout Clearance from side edge 130 mm 120 mm 80 mm ClearancesCG602 Series CG902 Series CG913 Series Clearance from rear edge 100 mm 90 mmGas Supply Connection Standards RequirementsClamping Down the Cooktop Flexible HosesLP Gas Gas Supply Connection CheckNatural Gas Turn on each gas valve and light each burnerCheck all burners have good flame see ,4,5 Minimum Setting or Turn DownTurn on main electrical supply and light the burners Replace the knobCG913TM Gas Rate SummaryCustomer Care Current Information New Zealand
Related manuals
Manual 17 pages 61.9 Kb Manual 11 pages 35.88 Kb

CG602 specifications

The Fisher & Paykel CG602 is a powerful and stylish gas cooktop that exemplifies the brand's commitment to high-quality kitchen appliances. Designed for home chefs who appreciate both aesthetics and functionality, the CG602 boasts an array of impressive features and technologies, making it a standout choice in the realm of cooking equipment.

One of the main features of the CG602 is its six high-efficiency gas burners, which deliver exceptional heat control and precision for various cooking methods. With a combination of high output and low simmer settings, users can easily sauté, boil, or create a delicate simmer—all with the turn of a knob. Specifically, the cooktop includes a powerful 19MJ/h burner, perfect for rapidly boiling water or achieving high-temperature cooking as well as smaller burners designed for simmering sauces and melting chocolate without the risk of burning.

The CG602 is also designed for ease of use and cleaning. The surface is crafted from durable stainless steel, ensuring longevity while being resistant to stains and scratches. This smooth finish makes it easy to wipe down after cooking, and the minimalistic design reduces the risk of food debris getting trapped in crevices, which is particularly advantageous in busy kitchen environments.

Another technological highlight of the CG602 is its intuitive flame failure safety device, which automatically cuts the gas supply if the flame is extinguished. This feature not only enhances safety while cooking but also promotes peace of mind for users concerned about gas leaks or hazards in the kitchen.

Installation is made effortless as the CG602 is designed for easy integration into various countertop designs. It can be seamlessly installed, whether in a contemporary or more traditional kitchen setting. The unit is also compatible with Fisher & Paykel's extensive range of kitchen appliances, allowing for a cohesive aesthetic in any home.

Additionally, the CG602 features convenient removable burner caps and grates, further simplifying cleaning and maintenance. Ultimately, the Fisher & Paykel CG602 is more than just a functional cooktop; it embodies a philosophy of craftsmanship and innovation, designed for culinary enthusiasts who demand both performance and style. This gas cooktop offers a practical and elegant solution for anyone looking to elevate their cooking experience.