Thermostat / Switch Mode | Enviro 50-830 specs

Operating Instructions

OPERATING YOUR PELLET STOVE:

PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed correctly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit.

DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN.

MANUAL MODE:

To START: Press the ON / OFF button. The stove will turn on. The system light will flash. The Auger Light will flash with each pulse of the auger (the Auger Feed Rate is pre-programmed during start-up). The Heat Level Indicator will show the Heat Level that the stove will run at after start-up.

If this is the first time the unit has been started or the unit has run out of fuel, the auger will need to be primed. Press the Manual Auger Feed button until fuel starts to drop into the Burn Pot Liner (see

“OPERATING INSTRUCTIONS - CONTROL BOARD FUNCTIONS”).

To OPERATE: When a fire has been established, the System Light will turn solid (after approximately 10

-15 minutes) and the Auger Light will continue to flash to the corresponding Heat Level setting. The Heat Level button can now be pressed at this time to change the desired Heat Level Output setting.

The convection blower (room air blower) will turn on. The speed of this blower is controlled by the setting of the heat level output indicator. The convection blower can be turned OFF by depressing the convection blower control button. When the air jacket reaches 160 °F (71 °C) the convection blower will come ON High, cooling the unit. For the best efficiency and to prevent cycling, the convection blower should be left on at all times.

When operating on LOW HEAT LEVEL, the feed rate can be adjusted, using the auger trim, for different quality fuels. These settings can be used if the fire keeps going out on low (for poor quality fuel) or if the

low setting is too hot for the room (see “OPERATING INSTRUCTIONS - CONTROL BOARD FUNCTIONS”).

THERMOSTAT / SWITCH MODE:

INITIAL START-UP: See above

OPERATION - HI / LOW mode: When the thermostat contacts are closed the stove settings are adjustable as per Manual Mode (see above). When the thermostat contacts open, the circuit board will take control of the settings. The stove will drop down to a low burn until the thermostat contacts close again. This low burn setting can be adjusted for different fuel qualities (see “OPERATING INSTRUCTIONS

-CONTROL BOARD FUNCTIONS”). The stove will come back to the previous HEAT LEVEL setting when the thermostat contacts close again.

OPERATION – ON / OFF mode: When the thermostat contacts close, the unit will light automatically. Once up to temperature, the stove operates the same as in manual mode (see above). When the thermostat contacts open, the unit automatically begins its shutdown routine. The stove will re-light when the thermostat contacts close again.

TURNING YOUR PELLET STOVE OFF:

•MANUAL and HI / LOW mode: To turn the unit OFF, simply press the ON / OFF button. This will stop the feed of pellets. The blowers will continue to operate and cool the stove down. When cool enough, the stove will turn off.

•ON / OFF mode: To turn the unit OFF, turn the thermostat down or off.

DO NOT unplug unit while Combustion fan is operating.

This may lead to smoke escaping from the stove.

50-830 specifications

The Enviro 50-830 is an innovative and versatile vehicle designed to address the growing need for efficiency and environmental sustainability in public transportation. With a focus on reducing emissions and enhancing the passenger experience, this model is becoming increasingly popular among transit agencies around the globe.

One of the standout features of the Enviro 50-830 is its advanced propulsion system. Equipped with a powerful yet eco-friendly engine, the vehicle demonstrates a commitment to reducing the carbon footprint while maintaining optimal performance. The engine complies with stringent emission standards, ensuring that it meets or exceeds environmental regulations.

The Enviro 50-830 also incorporates cutting-edge technologies designed for both safety and comfort. It includes advanced driver assistance systems (ADAS) that enhance safety for passengers and pedestrians alike. Features such as collision avoidance, lane-keeping assistance, and adaptive cruise control provide drivers with the necessary support to navigate busy urban environments safely.

In addition to safety, passenger comfort is a top priority for the Enviro 50-830. The interior is thoughtfully designed to offer a spacious and welcoming atmosphere. High-backed, ergonomic seating ensures comfort during travel, while ample legroom and wide aisleways facilitate easy movement. The vehicle is also equipped with Wi-Fi connectivity, real-time arrival information displays, and USB charging ports to cater to the needs of modern commuters.

Durability and reliability are key characteristics of the Enviro 50-830. Built with high-quality materials, the vehicle is designed to withstand the rigors of daily service while requiring minimal maintenance. This not only protects the investment for transit agencies but also ensures consistent service for passengers.

Additionally, the Enviro 50-830 embraces a modular design that allows for easy customization to meet varying operational needs. Agencies can tailor the configuration of the seating, features, and technologies to suit their specific requirements while still benefiting from a robust and efficient platform.

Overall, the Enviro 50-830 stands out as a forward-thinking solution for public transportation. By integrating sustainable practices, advanced technology, and passenger-centered design, it is setting a new standard for the future of urban mobility. Transit agencies looking to modernize their fleet while promoting a greener environment will find the Enviro 50-830 to be an ideal choice.