Enviro 50-830 owner manual Operating Instructions, Circuit Board Control Panel Decal

Page 7

Operating Instructions

CONTROL BOARD FUNCTIONS:

1.AUGER TRIM: Used to change feed rates on LOW ONLY for poorer quality fuels. Push the Auger Trim button until the number 1 and 5 lights appear on the Heat Level Indicator. This will increase the feed rate to four (4) seconds ON time Auger pulse. This is done only on LOW to allow the burning of poor quality fuels. Push the button until the number 1 and 4 lights appear, this will reduce the Auger On time to two (2) second. This setting is for high-grade fuel only. Push the button until just the number 1 light is on, this is for a three (3) second on time (standard setting).

 

 

 

1

7

2

 



 

3

 

4

 

 

 

5

 



8

6

 

 

Figure 3: Circuit Board Control Panel Decal.

2.CONVECTION BLOWER CONTROL: Used to turn the convection blower ON/OFF. If the Blower is left off, and the sensor located on the air jacket reaches 160 °F (71 °C), the Convection blower will automatically come on HI speed to cool the unit. Leave the convection blower ON for peak efficiency

3.AUGER PULSE LIGHT: This light will flash in conjunction with the auger.

4.MANUAL AUGER FEED: If the unit runs out of fuel, this button can be used to “prime the auger system”. This button will turn off after 60 seconds and then must be released and pressed again.

5.SYSTEM LIGHT: Responsible for signaling the state of the control board. When the light is flashing during start- up, the stove is in an automatic start mode. When the light is solid, the Heat Level Setting can be altered.

6.ON/OFF BUTTON: Used to turn the unit ON and OFF.

7.HEAT OUTPUT INDICATOR: Shows the present heat output setting.

8.HEAT LEVEL ADJUSTMENT: When pressed, will change the heat setting of the unit from low to high.

Auger Trim

Auger Trim

Auger Trim

4 2 Seconds "ON"

5

3 Seconds

 

4 Seconds

"ON"

 

"ON"

Factory Setting

 

 

 

1

1

1

Figure 4: Auger trim and heat level indicator.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Meridian Table of Contents Store pellets at least 36 1 m away from the pellet stove IntroductionUSE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel 32 1/2 826mm 24 7/8 24 3/4 632mm 629mm Circuit Board Control Panel Decal Operating InstructionsInitial START-UP See above Thermostat / Switch ModeSpecial Notes Slider / Damper Must be SET AT Time of InstallationBurn POT and Liner 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Door Glass Cleaning 2-3 daysDo not Place Unburned or RAW Pellet Fuel in ASH PAN Firebox Panel Installation of firebox backingPost Season CLEAN-UP Cleaning Plated SurfacesTo the Distributor WarrantyFor the do-it-yourself Individual Name of Owner Address Installation Data Sheet

50-830 specifications

The Enviro 50-830 is an innovative and versatile vehicle designed to address the growing need for efficiency and environmental sustainability in public transportation. With a focus on reducing emissions and enhancing the passenger experience, this model is becoming increasingly popular among transit agencies around the globe.

One of the standout features of the Enviro 50-830 is its advanced propulsion system. Equipped with a powerful yet eco-friendly engine, the vehicle demonstrates a commitment to reducing the carbon footprint while maintaining optimal performance. The engine complies with stringent emission standards, ensuring that it meets or exceeds environmental regulations.

The Enviro 50-830 also incorporates cutting-edge technologies designed for both safety and comfort. It includes advanced driver assistance systems (ADAS) that enhance safety for passengers and pedestrians alike. Features such as collision avoidance, lane-keeping assistance, and adaptive cruise control provide drivers with the necessary support to navigate busy urban environments safely.

In addition to safety, passenger comfort is a top priority for the Enviro 50-830. The interior is thoughtfully designed to offer a spacious and welcoming atmosphere. High-backed, ergonomic seating ensures comfort during travel, while ample legroom and wide aisleways facilitate easy movement. The vehicle is also equipped with Wi-Fi connectivity, real-time arrival information displays, and USB charging ports to cater to the needs of modern commuters.

Durability and reliability are key characteristics of the Enviro 50-830. Built with high-quality materials, the vehicle is designed to withstand the rigors of daily service while requiring minimal maintenance. This not only protects the investment for transit agencies but also ensures consistent service for passengers.

Additionally, the Enviro 50-830 embraces a modular design that allows for easy customization to meet varying operational needs. Agencies can tailor the configuration of the seating, features, and technologies to suit their specific requirements while still benefiting from a robust and efficient platform.

Overall, the Enviro 50-830 stands out as a forward-thinking solution for public transportation. By integrating sustainable practices, advanced technology, and passenger-centered design, it is setting a new standard for the future of urban mobility. Transit agencies looking to modernize their fleet while promoting a greener environment will find the Enviro 50-830 to be an ideal choice.
Top Page Image Contents