Enviro 50-1573 ASH PAN and Door Gaskets weekly, ASH PAN weekly, Pellet Fuel in ASH PAN

Page 11

Routine Cleaning and Maintenance

If the glass has build up that can not be removed with only the cloth, clean the glass using paper towel and a gas appliance glass cleaner, this may be purchased through most dealers. If a gas appliance glass cleaner is not available, use a damp paper towel dipped in fly ash to clean the glass. After the glass has been cleaned use the dry soft cloth to wiping down the outside and inside of the glass.

ASH PAN AND DOOR GASKETS (weekly)

After extended use the gasketing may come loose. To repair this, glue the gasketing on using high- temperature fiberglass gasket glue available from your local dealer. This is important to maintain an airtight assembly.

ASH PAN (weekly)

IMPORTANT: The unit must be OFF while the ash pan is removed. Sweep the ashes from the firebox through the grate into the ash pan.

The ash pan is located, in the pedestal, and has a latching mechanism to secure it. To remove the ash pan open the cover from the right hand side, unlock the latch on the pedestal cover and pull the pan out. If the ash pan is hot and/or dirty, gloves should be worn to remove it. Pull the ash pan out. When the ash pan is out of the unit lift the ash pan by the front and back handles and carry the ash pan to where the ashes will be emptied.

Figure 10: Pulling Ash Pan Out.

Dump the ashes into a metal container stored away from combustibles. Monitor the ash level every week. Remember that different pellet fuels will have different ash contents. Ash content is a good indication of fuel efficiency and quality. Refer to “SAFETY WARNINGS AND RECOMMENDATIONS” for disposal of ashes. Vacuum the inside of the ash pan compartment inside the pedestal including the hole at the top back of the compartment. Replace the ash pan and close pedestal door. DO NOT PLACE UNBURNED OR RAW

PELLET FUEL IN ASH PAN.

Heat exchanger tubes

EXHAUST PASSAGES (biannually)

cleaner handle.

Removal of the firebox backing for biannual cleaning

 

 

• Open the door by lifting the handle, remove the

 

 

burn pot and burn pot liner.

 

•

Lubricate all screws with penetrating oil.

 

• Remove the four (4) screws that hold the side panels

 

 

in place.

 

•

With the tip of a flat screwdriver, gently lift up the

 

 

side panels and remove the side panels.

 

•

Pull the center panel out.

 

•

Vacuum thoroughly.

 

Installation of firebox backing:

 

•

Insert center panel.

 

•

Place the side panels back into the firebox and re-

 

 

install the two (2) screws on each side.

Vacuum inside ash box

•

Replace the glass door and secure.

 

•

Clean thoroughly.

Figure 11: Evolution Open.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Evolution Table of Contents Store pellets at least 36 1 m away from the pellet stove IntroductionUSE of Cordwood is Prohibited by LAW Safety Warnings & RecommendationsSafety Warnings & Recommendations Hearth Pad SpecificationsUnit Overheated Operating InstructionsManual Mode Efficient Flame Special NotesBurner POT and Liner 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Door Glass Cleaning 2-3 daysExhaust Passages biannually ASH PAN and Door Gaskets weeklyASH PAN weekly Pellet Fuel in ASH PANControl Board Error Messages Post Season CLEAN-UPCleaning Plated Surfaces Door Glass ReplacementName of Owner Address Installation Data Sheet

50-1573 specifications

The Enviro 50-1573 is an innovative and eco-friendly solution aimed at addressing the growing needs of businesses and consumers alike. This product is designed with a focus on sustainability without compromising on performance or functionality.

One of the most notable features of the Enviro 50-1573 is its advanced energy efficiency technology. It uses state-of-the-art mechanisms to minimize energy consumption, making it an ideal choice for environmentally conscious users. Its design incorporates high-efficiency components that significantly reduce the carbon footprint while still delivering optimal performance. This efficiency not only helps the environment but also results in cost savings for users.

The Enviro 50-1573 is built using sustainable materials, which is a crucial characteristic for modern consumers. The use of recycled and non-toxic materials ensures that the product is safe for both the user and the planet. Manufacturers prioritize the lifecycle impact of their products, ensuring that they are designed to be recyclable or biodegradable at the end of their use.

In terms of technology, the Enviro 50-1573 incorporates smart features that enhance user experience. It includes an intuitive control system that allows users to monitor performance and make adjustments easily. This technology can be further integrated with mobile applications, allowing for remote operation and real-time tracking of energy usage and efficiency metrics.

Safety is another key characteristic of the Enviro 50-1573. It is designed with multiple safety protocols to protect users and surrounding environments, ensuring peace of mind during operation. These protocols include overload protection and automatic shut-off features, which help to prevent accidents and energy waste.

Moreover, the Enviro 50-1573 offers versatility, as it can be used in a variety of settings, from residential to commercial applications. Its streamlined design allows it to fit seamlessly into any environment without being obtrusive.

In conclusion, the Enviro 50-1573 stands out in the market for its commitment to sustainability, energy efficiency, and user-friendly technology. By prioritizing eco-friendliness alongside cutting-edge features, it meets the demands of today’s environmentally aware consumers while providing unwavering performance. Whether for home or business use, the Enviro 50-1573 represents a forward-thinking approach to products designed for a sustainable future.
Top Page Image Contents