Desa Tech CSPINT Operating Heater, For Your Safety Read Before Lighting, Lighting Instructions

Page 13

OPERATING HEATER

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result causing property damage, per- sonal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighborʼs phone. Follow the gas supplierʼs instructions.

•If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, donʼt try to repair it, call a qualified service tech- nician or gas supplier. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orangeflamewillalsobepresent. Open a window to vent smell. This will only last a few hours.

1.STOP! Read the safety information, abovc.

2.Make sure equipment shutoff valve is fully open.

3.Turn control knob clockwise to the OFF position.

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information, column 1. If you donʼt smell gas, go to the next step.

5.Turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds (see Figure 16).

Note: You may be running this heater for the first time after hooking up to gas sup- ply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

6.With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 14.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. Wait one (1) minute for system to reset before lighting pilot again.

8.Turn control knob counterclockwise to desired heating level. The burners should light. Set control knob to any heat level between HI and LO.

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

Ignitor Button

Control Knob

Figure 16 - Control Knob and Ignitor

Button Location

Thermocouple

Pilot Burner

Figure 17 - Pilot

111487-01E

www.desatech.com

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Models CSBNT, CSBPT, CSPBNT, CSPBPT, CSPINT, Cspipt What to do if YOU Smell GASTable of Contents Safety Information Local Codes Product IdentificationProvide adequate clearances around air openings AIR for Combustion Ventilation Product FeaturesVentilation AIR Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside BuildingVentilation Air From Outdoors AIR for Combustion Ventilation UnpackingCheck GAS Type InstallationClearances to Combustibles Vent-Free Operation Only Minimum Wall and Ceiling Clearances see ,Installation Items Needed Connecting to GAS SupplyFront View Top ViewBack View Petroleum LP gasTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Correct all leaks at onceInstalling ROD and Screen Installing LOG SETStove cavity see Figure Wall clearances as outlined onOperating Heater For Your Safety Read Before LightingLighting Instructions Inspecting Burners Cleaning MaintenanceLogs Burner Injector Holder and Pilot AIR Inlet HoleBlow air into the primary air holes on the injector holder Replace logs if broken or chipped dime-sized or largerObserved Problem Possible Cause Remedy TroubleshootingBurner orifice clogged Clean burner see Cleaning Delayed ignition burnerWhen burner is lit Dark residue on logs or inside Improper log placementStatement at top Gas leak. See WarningService Hints SpecificationsTechnical Service Replacement PartsIllustrated Parts Breakdown Parts List Stove Body Models CSB SERIES, Cspb Series and Cspi Series Parts Centrals Keep this Warranty Warranty Information
Related manuals
Manual 24 pages 61.37 Kb

CSPBPT, CSPINT, CSPIPT, CSBPT, CSBNT specifications

Desa Tech CSPBNT, CSBNT, CSBPT, CSPIPT, and CSPINT represent a suite of advanced technologies tailored for innovative applications in various sectors, notably in communications, security, and data processing. Each product within this family boasts unique features while sharing common underlying technologies, making them indispensable tools in modern technological landscapes.

Desa Tech CSPBNT, short for Communication Signal Processing in Broadband Networks Technology, focuses on enhancing connectivity and bandwidth efficiency. Its main feature is the ability to optimize signal transmission over long distances, ensuring minimal data loss and latency. This technology employs advanced modulation techniques and error correction algorithms, which not only improve overall network reliability but also expand the range of serviceable areas in both urban and rural settings.

CSBNT, the Communication Security Broadband Network Technology, prioritizes data integrity and security. Featuring robust encryption protocols and real-time monitoring systems, CSBNT is engineered to protect sensitive information from cyber threats. Its adaptive security layers allow organizations to tailor their defenses based on evolving threat landscapes, making it an essential tool for industries handling confidential data.

CSBPT, or Communication Signal Booster Processing Technology, enhances signal strength and quality in weak reception areas. This technology utilizes smart antennas and digital signal processing to amplify weak signals and filter out noise, providing a stable communication line even in challenging environments. Its crucial applications span telecommunication, emergency services, and remote operations.

CSPIPT, signifying Communication Software for Intelligent Processing and Transmission, integrates machine learning algorithms to predict and optimize data flow. This feature enables adaptive bandwidth allocation and enhances user experience by prioritizing critical applications. CSPIPT is particularly useful in environments where every millisecond counts, such as financial trading platforms and real-time analytics systems.

Lastly, CSPINT, or Communication Systems Planning and Integration Technology, focuses on system interoperability and seamless integration. It simplifies the communication process between diverse systems, ensuring they cooperate efficiently and effectively. This technology is vital for organizations that rely on complex systems, as it boosts operational efficiency and reduces downtime.

Together, these advanced technologies offered by Desa Tech provide a comprehensive toolkit designed to meet the demands of today's fast-paced and interconnected world, emphasizing efficiency, security, and adaptability across multiple platforms and use cases.
Top Page Image Contents