Carrier 09BY006-024 dimensions Equip, Fmc, Gnd

Page 12

Determine maximum deviation from average voltage:

(AB) 243 ± 239 = 4 v (BC) 239 ± 236 = 3 v (AC) 239 ± 238 = 1 v

Maximum deviation is then 4 v. To determine the percentage of voltage imbalance:

% Voltage Imbalance = 100 x

 

4

239

 

= 1.7%

 

 

This amount of phase imbalance is satisfactory since it is below the allowable maximum of 2%.

IMPORTANT: If supply voltage phase imbalance is more than 2%, contact your local electric utility com- pany immediately.

Condenser operation on improper line voltage or exces- sive phase imbalance may be considered abuse and any re- sulting damage may not be covered by Carrier warranty.

All wiring must be in accordance with local or NEC (National Electrical Code) regulations. Refer to Fig. 11 for combination ®eld wiring.

MAIN POWER WIRING Ð The units must have adequate overcurrent protection, fuses, or HACR (Heating, Air Conditioning and Refrigeration) breakers, according to the national and applicable local codes.

For ®eld power connections, all main power wiring enters the unit through a factory-punched access hole under the con- trol box. Attach power wires to the 3 power connections in the unit control box using ®eld-supplied wirenuts. Be sure to install a ground wire. See Fig. 11.

CONTROL CIRCUIT POWER WIRING Ð Connect 24-v control wires to the 2 low-voltage connections at the com- pressor contactor. Use ®eld-supplied wirenuts to make the connections in the control box low-voltage section.

GENERAL WIRING NOTES

1.Power entry is at one end only.

2.Fan motors are thermally protected. All motors are pro- tected against primary single-phasing conditions.

3.Replacement of factory wires must be with appliance wir- ing material rated 105 C or its equivalent.

4.Factory wiring is in accordance with NEC. Field modi- ®cations or additions must be in compliance with all ap- plicable codes.

 

LEGEND

EQUIP

Ð Equipment

FMC

Ð Fan Motor Contactor

GND

Ð Ground

 

Field Wiring

 

Factory Wiring

 

Field Splice

 

Marked Terminal

Fig. 11 Ð Combination Field Wiring

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Contents Safety ConsiderationsInstallation General09BY Unit 008-014 Shown Mounting Applications 09BY Dimensions English Dimension006 008 012 014 016,024 Ft-in 006 008 012 014 016,024Unit Size Unit APPROX. Shaft LengthCondenser Unit Application Physical DataThreaded Rod Installed in Bracket Rig and Place UnitInstall Rain Drain See Fig Complete Refrigerant PipingLength of Pipe Unit Hot Gas LiquidHot Gas Liquid Qty Dimensions Condenser Ductwork DetailsUnit Voltage Supply Voltage FAN Power Supply Electrical DataFLA MCA FLAEquip FMCGND Service Cleaning Condenser CoilsCondenser Fan Adjustment START-UPCondenser Fan Performance Unit AirflowExternal Static Pressure in. wg 09BY Cfm Rpm Bhp Maintenance Troubleshooting TroubleshootingProblem Potential Cause Solution Page Copyright 1996 Carrier Corporation START-UP Checklist Preliminary InformationPre-Start-Up Start-Up Check Voltage Imbalance

09BY006-024 specifications

The Carrier 09BY006-024 is a high-efficiency air conditioning unit designed to provide reliable cooling solutions for both residential and commercial spaces. Known for its innovative technologies and superior performance, this model is specifically engineered to ensure optimal indoor comfort while minimizing energy consumption.

One of the standout features of the 09BY006-024 is its advanced inverter technology. This system allows the unit to adjust its cooling capacity according to the ambient temperature, resulting in significant energy savings. The inverter compressor operates at variable speeds, which not only reduces electricity bills but also enhances the overall lifespan of the unit by minimizing wear and tear.

The 09BY006-024 is equipped with an environmentally friendly refrigerant, R-410A, which is designed to have a minimal impact on the ozone layer and offers better thermal efficiency compared to traditional refrigerants. This makes it a suitable choice for environmentally conscious consumers looking to reduce their carbon footprint without compromising on cooling performance.

Furthermore, this model features a robust filtration system that includes a multi-stage filter designed to trap airborne pollutants, allergens, and dust particles. This ensures that the air circulated within the living or working space remains clean and healthy. The filters are easily accessible and can be cleaned or replaced, making maintenance hassle-free.

For user convenience, the Carrier 09BY006-024 comes with a user-friendly remote control and has options for smart home integration. This allows users to monitor and adjust settings from their smartphones or tablets, providing flexibility and control over their indoor climate.

In terms of design, the unit boasts a sleek and modern appearance, making it a stylish addition to any setting. Its compact size ensures that it can fit into various installation spaces without taking up valuable room.

Another key characteristic is its quiet operation. The Carrier 09BY006-024 is engineered with noise-reducing technologies that allow it to operate quietly, ensuring that it does not disrupt the peace in homes or workplaces.

In summary, the Carrier 09BY006-024 combines innovative technology, energy efficiency, and user-friendly features to deliver an exceptional cooling experience. Its commitment to environmental responsibility, combined with high-performance capabilities, makes it a top choice for anyone looking to enhance their indoor comfort.
Top Page Image Contents